Publicité
Les langues disponibles
Les langues disponibles
General Safety Warnings
WARNING: Failure to follow the warnings and instructions may result in damage to the tool
or serious injury.
Save all warnings and instructions for future reference.
WARNING: This tool is not intended for use by persons (including children) with reduced
physical or mental capabilities or lack of experience or knowledge unless they have been given
supervision or instruction concerning use of the tool by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the appliance.
a) Familiarise yourself with the applications, limitations and hazards of the tool.
b) Keep the product in good working order and condition. Take immediate action to repair or
replace damaged parts.
c) Use recommended parts only. Unapproved parts may be dangerous and will invalidate the
warranty.
d) Use the tool only for its intended purpose.
e) Use appropriate safety equipment including eye protection, respiratory protection and protective
gloves.
f) Injury can occur if loose clothing, personal jewellery, neck wear, hair or gloves are not kept away
from the tool and its accessories.
g) Keep proper footing and balance at all times. If appropriate secure workpiece in a clamp or vice.
h) Ensure that the tool is disconnected from the air supply before servicing, changing accessories
and when not in use.
i) DO NOT allow smoking or open flames in the work area.
j) DO NOT modify the tool. Modifications can reduce the effectiveness of safety measures and
increase the risks to the user.
k) DO NOT tamper with or adjust safety valves or other safety features.
l) DO NOT use the tool or accessories if they have been damaged. Inspect tools and accessories
before each use. Do not use if damaged or excessively worn.
m) DO NOT use whilst tired or under the influence of drugs, alcohol or medication.
n) Compressed air can cause severe injury.
o) Whipping hoses can cause severe injury. Always check for damaged or loose hoses and fittings.
p) DO NOT direct air flow at yourself, others or animals.
q) Do not exceed the maximum air pressure stated on the tool.
r) Never carry an air tool by the hose.
s) Air tools should only be powered by compressed air at the lowest pressure required by the task to
reduce noise and vibration and minimise wear.
t) Hold the tool correctly; be ready to counteract normal or sudden movements such as recoil. Have
both hands available.
u) Never use pure oxygen or combustible gases to power an air tool. Air tools are not designed for
these power sources and their use creates a fire and explosion hazard.
v) Switch off tool if air / power supply is interrupted.
w) Be aware that air tools may become cold during use, affecting grip, control and susceptibility to
vibration-related injury.
IMPORTANT: Even when this tool is used as prescribed it is not possible to eliminate all residual risk
factors. If you are in any doubt as to the safe use of this tool, do not use it.
Work area hazards
1) Be aware of slippery surfaces caused by use of the tool and trip hazards caused by the air line.
Slips, trips and falls are major causes of injury.
2) Where possible do not obstruct thoroughfares and passageways with air lines or cables. Take
appropriate measures to reduce trip risk such as erecting warning signs and fixing cables and air
lines in place.
3) The tool is not intended for use in potentially explosive atmospheres and is not insulated against
contact with electric power.
Air Grease Gun 400cc
Product Familiarisation
1.
Outlet Nozzle
2.
Grease Gun Body
3.
Trigger
4.
Quick Connector
5.
Plunger Handle
6.
Plunger Release
7.
Chamber
8.
Flexible Hose
9.
Rigid Pipe
10. Coupler
11. Filler Pump Nozzle
12. Bleed Valve
Intended Use
Grease dispensing gun, powered by compressed air from a compressor, suitable for bulk and
cartridge grease.
Not intended for commercial use.
The tool must ONLY be used for its intended purpose. Any use other than those mentioned in this
manual will be considered a case of misuse. The operator, and not the manufacturer, shall be liable
for any damage or injury resulting from such cases of misuse. The manufacturer shall not be liable
for any modifications made to the tool, nor for any damage resulting from such modifications.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Familiarise yourself with all its features and functions.
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool.
Before Use
Fitting the quick connector
This tool is supplied with two different male airline quick connectors (Fig. I):
EQ-4 – commonly used in Europe
EN-6 – mainly used in the UK
• Please choose the connector that is compatible with the airline system you are using, and install
as outlined below:
1. Apply some PTFE tape (not included) to the screw threads of the Quick Connector (4). This will
help to maintain an air-tight seal
Note: Apply PTFE tape tightly and in a clockwise direction, so it does not come off when the thread
is screwed into the tool.
2. Remove the protective plug from the air inlet
3. Using a spanner (not included) screw the quick connector into the air inlet located at the base of
the handle
4. Connect to airline, pressurise carefully and carry out a leak check (e.g. by spraying small
amounts of soapy water on to the outside of the connectors)
• Air lines fitted with matching female quick connectors will now be a push fit to the tool
silverlinetools.com
5
Publicité
