Skil 9004 Notice Originale page 9

- provide for a secure stance
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust fl y
away from the body
- keep ventilation slots J 2 uncovered
APPLICATION ADVICE
• Instead of fl ange E 2 the "CLIC" quick-clamping fl ange
(SKIL accessory 2610388766) can be used; grinding/
cutting discs can then be mounted without the use of
accessory keys
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially ventilation
slots J 2)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skilmasters.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol ! will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents: EN 60745, EN 55014, in
accordance with the provisions of the directives
2006/95/EC, 2004/108/EC, 98/37/EC (until Dec. 28,
2009), 2006/42/EC (from Dec. 29, 2009 on)
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
Arno van der Kloot
Vice President
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
16.11.2009
Jan Trommelen
Approval Manager
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 84 dB(A) and the sound
power level 95 dB(A) (standard deviation: 3 dB), and the
vibration when surface grinding 3.0 m/s² (hand-arm
method; uncertainty K = 1.5 m/s²)
! other applications (such as cutting-off) may have
different vibration values
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
signifi cantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
signifi cantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
F
Meuleuse d'angle
INTRODUCTION
• Cet outil sert au meulage, au tronçonnage et à
l'ébarbage léger de pièces en métal et en pierre sans
utiliser de l'eau
• Ne jamais appliquez une trop forte pression sur
l'outil; laissez au disque le soin de faire le travail de
par sa propre vitesse
• Les opérations de coupe avec disques à tronçonner
abrasifs ne sont autorisées que si une protection de
tronçonnage (disponible en option comme
accessoire SKIL 2610399439) est utilisée
• Lisez et conservez ce manuel d'instruction 3
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Poignée auxiliaire
B Protège-main
C Arbre
D Bride de montage
E Bride de serrage
F Clé
G Bouton de blocage de l'arbre
H Interrupteur marche/arrêt de verrouillage
J Fentes de ventilation
9
9004