BH FITNESS COMFORT EVOLUTION H855 Instructions De Montage Et Utilisation page 10

plain washers (3), and tighten securely.
3
FITTING THE HANDLEBAR
Carefully insert handlebar (5) in position
indicated in Fig2 through the lateral hole on the
chain cover, as marked with an arrow. Once
introduced turn it 180º untill tha handlebar leans
on the structure. Place the bracket (6), put the
screw (8) and the washer (7) and tighten
strongly.
4
FITTING THE SADDLE PROFILE
Firstly (Fig 3), place the saddle profile (14) close
to the main chain cover (1) and connect terminal
(12) with terminal (17) from saddle profile (14).
Afterwards introduce tube of main body in
aluminium profile, paying special attention to the
cables. Finally, place screw (4) and washer (3)
and tighten securely.
5
FITTING THE REAR SUPPORT
Take the rear stabiliser bar (19) and position it
on the machine's rear stand bracket support
(18), as shown in (Fig. 4), inserts bolts (4), fit
the plain washers (3) and tighten securely.
Get rear support (18) with rear stabilizer
mounted and place it in the aluminium profile as
indicated in (Fig 5). Tighten strongly nuts (J) to
screws (C). Fit the rear trim (39) .
6
ATTACHING THE SADDLE
Place saddle back support tube to the upright
position (Fig6). Get screw (25) and place it in
the metallic support piece. Place washer and
nut and tighten securely.
Afterwards, unscrew the screws (28) on the
back side of the saddle back, place it as shown
in (Fig 7) and tighten back again the screws
securely.
7
FITTING THE PEDALS
The assembly instructions for the pedals must
be followed to the letter, fitting these incorrectly
could damage the screw thread on either the
pedal or the crank.
Right and left refer to the position that the user
adopts when sitting on the saddle to do the
exercises.
The right-hand pedal (16), marked with the letter
(R), screws onto the right-hand crank, also
marked with an (R), in a clockwise direction.
Tighten securely, (Fig. 8).
The left-hand pedal (15), marked with the letter
(L), screws onto the left-hand crank, also
marked with an (L), in an anti-clockwise
direction. Tighten securely, (fig 8).
Once the pedals have been fitted, insert the end
of the pedal clip (1) into the slot on the pedal (2)
adjusting it to your footwear on the ledge of the
pedal (3), (Fig. 9A).
8
FITTING THE MONITOR
Get the monitor (9), (Fig 9) and connect speed
sensor cable (11) with cable (12). Afterwards
connect terminal (10) with terminal (13). Finally,
introduce the monitor in the main body (A), firts
the lower side and then the upper side.
9
ADJUSTING SADDLE BACK
Place cup 31 in the upper hole on the saddle
back tube end as indicated in Fig 13. To move
the saddle back, push button B (Fig 13), move it
forward or backwards until it is located on the
desired position and release the button. Verify
that the saddle back is perfectly secured in one
of the three possible positions.
10
LEVELLING.
Once the unit has been placed into its final
position, make sure that it sits flat on the floor
and that it is level. This can be achieved by
screwing the adjustable feet (E) up or down, as
shown in (Fig 10).
11
EXERTION SETTINGS.
.
(Mod. H-855)
exertion during exercise, this appliance is
equipped with a tensioning control (100),
offering various exertion settings,( Fig. 7).
To increase pedal resistance turn the tensioning
control (100) clockwise (+) until the exertion
level best suits your exercise requirements. To
reduce pedal resistance turn the tensioning
control (100) anticlockwise (-).
12
MOVEMENT & STORAGE
The unit is equipped with wheels (40) to make it
easier to move. The wheels located at the front
of your unit make it easier to move it into a
chosen position, by lifting the rear of the unit up
slightly and pushing it, as shown in (Fig 11).
Store your unit in a dry place, preferably not
subject to changes in temperature.
13
MAINS CONNECTION
(Mod H-856)
Insert the jack (g) on the transformer (c) into the
connection hole (h) on the main body (A)
(bottom, rear of the machine) and then plug the
transformer into a 220 V mains supply, (Fig 12).
10
To provide an even level of