Publicité
Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety Warnings for Sander
Only use the power tool for dry sanding. Water entering
u
a power tool will increase the risk of electric shock.
Warning: Danger of fire! Avoid overheating the work-
u
piece and the sander. Always empty the dust collector
before taking a break from work. Sanding dust in the
dust bag, microfilter, paper bag (or in the filter bag or va-
cuum cleaner filter) can spontaneously combust under
certain conditions, for example if flying sparks are cre-
ated when sanding metals. This risk is increased if the
sanding dust is mixed with paint or polyurethane residue
or with other chemical substances and if the workpiece is
hot as a result of prolonged work.
Clean the air vents on your power tool regularly. The
u
motor's fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Always wait until the power tool has come to a com-
u
plete stop before placing it down.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
Technical Data
Orbital sander
Article number
Rated power input
No-load speed
No-load orbital stroke rate
Orbit diameter
Sanding sheet dimensions
– Clamping tension
Sanding plate dimensions
Bosch Power Tools
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for dry sanding of wood, plastic,
dry walls, filler and varnished surfaces.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch
(2) Rear clamping bracket
(3) Sanding plate
(4) Sanding sheet clamps (x 2)
a)
(5) Abrasive disc
(6) Front clamping bracket
(7) Handle (insulated gripping surface)
(8) Complete dust bag (GSS 140 A)
(9) Extraction outlet (GSS 140 A)
a)
(10) Extraction hose
(GSS 140 A)
a)
(11) Punch
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GSS 140
3 601 BA8 ...
W
–1
min
14,000
–1
min
28,000
mm
mm
114 x 140
mm
101 x 112
English | 13
GSS 140 A
3 601 BA8 ...
220
220
14,000
28,000
1.5
1.5
114 x 140
101 x 112
1 609 92A 8RN | (03.08.2023)
Publicité
