Publicité
Les langues disponibles
Les langues disponibles
INDEX
1.
GENERAL WARNINGS
2.
PRODUCT DESCRIPTION AND INTENDED USE
3.
PACKAGE CONTENTS
4.
PRODUCT COMPONENT DESCRIPTION
5.
TYPE OF SYSTEM
6.
INSTALLATION
6.1
Tools and materials
7.
MAINTENANCE
7.1
Periodic maintenance
8.
PRODUCT TECHNICAL DATA SHEET
8.1
Technical data
9.
LIMITATIONS OF USE
10.
DECLARATION OF CONFORMITY
1. GENERAL WARNINGS
THANK YOU
Thank you for purchasing a Fadini product.
Please read these instruc�ons carefully before using this
appliance. The instruc�ons contain important informa�on
which will help you get the best out of the appliance and ensure
safe and proper installa�on, use and maintenance. Keep this
manual in a convenient place so that you can always refer to it
for the safe and proper use of the appliance.
INTRODUCTION
This operator is designed for a specific scope of applica�ons as
indicated in this manual, including safety, control and signaling
accessories as minimum required with Fadini equipment. □ Any
applica�ons not explicitly included in this manual may cause
opera�on problems or damages to proper�es and people. □
Meccanica Fadini S.r.l. is not liable for damages caused by the
incorrect use of the equipment, or for applica�ons not included
in this manual or for malfunc�oning resul�ng from the use of
materials
or
accessories
manufacturer. □ The manufacturer reserves the right to make
changes to its products without prior no�ce. □ All that is not
explicitly indicated in this manual is to be considered not
allowed.
BEFORE INSTALLATION
Before commencing operator installa�on assess the suitability
of the access, its general condi�on and the structure. □ Make
sure that there is no risk of impact, crushing, shearing,
conveying, cu�ng, entangling and li�ing situa�ons, which may
prejudice people safety. □ Do not install near any source of heat
and avoid contacts with flammable substances. □ Keep all the
accessories able to turn on the operator (transmi�ers,
proximity readers, key-switches, etc) out of the reach of the
children. □ Transit through the access only with sta�onary
operator. □ Do not allow children and/or people to stand in the
proximity of a working operator. □ To ensure safety in the whole
movement area of a gate it is advisable to install photocells,
sensi�ve edges, magne�c loops and detectors. □ Use
yellow-black strips or proper signals to iden�fy dangerous
spots. □ Before cleaning and maintenance opera�ons,
disconnect the appliance from the mains by switching off the
master switch. □ If removing the actuator, do not cut the
electric wires, but disconnect them from the terminal box by
loosening the screws inside the junc�on box.
CE DECLARATION OF CONFORMITY of the manufacturer:
Meccanica Fadini S.r.l. (Via Mantova, 177/A - 37053 Cerea - VR - Italy) declares under own responsibility that: FOX complies with the 2006/42/CE Machinery Direc�ve, and
also that it is sold to be installed in an "automa�c system", along with original accessories and components as indicated by the manufacturing company. An automa�c gate
operator is, by law, a "machinery" and therefore the installer must fit the equipment with all of the applicable safety norms. The installer is also required to issue the
installer's Declara�on of Conformity. The manufacturer is not liable for possible incorrect use of the product. The product complies with the following specific norms:
analysis of the risks and subsequent ac�on to cure them as per EN 12445 and EN 12453, Low Voltage Direc�ve 2014/35/UE, Electromagne�c Compa�bility 2014/30/UE.
In order to cer�fy the product, the manufacturer declares under own responsibility the compliance with the EN 13241-1 PRODUCT NORMS.
Tested and cer�fied:
marking and type tes�ng according to ITT PDC No. 2392-2008.
The CE conformity declara�on can be downloaded from the website www.fadini.net.
not
recommended
by
INSTALLATION
All installa�on opera�ons must be performed by a qualified
technician, in observance of the Machinery Direc�ve
2006/42/CE and safety regula�ons EN 12453 - EN 12445. □
Verify the presence of a thermal-magne�c circuit breaker 0,03 A
- 230 V - 50 Hz upstream the installa�on. □ Use appropriate
objects to test the correct func�onality of the safety
accessories, such as photocells, sensi�ve edges, etc. □ Carry out
a risk analysis by means of appropriate instruments measuring
the crushing and impact force of the main opening and closing
edge in compliance with EN 12445. □ Iden�fy the appropriate
solu�on necessary to eliminate and reduce such risks.□ In case
where the gate to automate is equipped with a pedestrian
entrance, it is appropriate to prepare the system in such a way
to prohibit the opera�on of the engine when the pedestrian
entrance is used. □ Apply safety nameplates with CE marking on
the gate warning about the presence of an automated
installa�on. □ The installer must inform and instruct the end
user about the proper use of the system by releasing him a
technical dossier, including: layout and components of the
installa�on, risk analysis, verifica�on of safety accessories,
verifica�on of impact forces and repor�ng of residual risks.
INFORMATION FOR END-USERS
The end-user is required to read carefully and to receive
informa�on concerning only the opera�on of the installa�on so
that he becomes himself responsible for the correct use of it. □
The end-user shall establish a wri�en maintenance contract
with the installer/maintenance technician (on -call). □ Any
maintenance opera�on must be done by qualified technicians.
□ Keep these instruc�ons carefully.
WARNINGS FOR THE CORRECT OPERATION OF THE
INSTALLATION
For op�mum performance of system over �me according to
safety regula�ons, it is necessary to perform proper
maintenance and monitoring of the en�re installa�on: the
automa�on, the electronic equipment and the cables
connected to these. □ The en�re installa�on must be carried
out by qualified technical personnel, filling in the Maintenance
Manual indicated in the Safety Regula�on Book (to be
the
requested
www.fadini.net/supporto/downloads).
maintenance inspec�on at least every 6 months, while for the
electronic equipment and safety systems an inspec�on at least
once every month is required. □ The manufacturer, Meccanica
Fadini S.r.l., is not responsible for non-observance of good
installa�on prac�ce and incorrect maintenance of the
installa�on.
DISPOSAL OF MATERIALS
Dispose properly of the packaging materials such as cardboard,
nylon, polystyrene etc. through specializing companies (a�er
verifica�on of the regula�ons in force at the place of installa�on
in the field of waste disposal). Disposal of electrical and
electronic materials: to remove and dispose through
specializing companies, as per Direc�ve 2012/19/UE. Disposal
of substances hazardous for the environment is prohibited.
GB - 20
or
downloaded
from
President of the Board
Meccanica Fadini S.r.l.
Paolo Fadini
FOX 724 | FOX 730
the
site
□
Operator:
Publicité
