Master HEAT GUN Mode D'emploi page 3

Important Safety Instructions
• Clean up all removed paint and dust
by wet mopping the floors. Use a wet
cloth to clean all walls, sills and any other
surface where paint or dust is clinging. DO
NOT SWEEP, DRY DUST OR VACUUM.
Use a high phosphate detergent or
trisodium phosphate (TSP) to wash and
mop areas.
• At the end of each work session put
the paint chips and debris in a double
TO OPERATE HEAT GUN
1. Plug heat gun into properly rated outlet.
2. Move rocker switch to "II" position. (VT
DU BEC OPÉRER À 'COLD' A LA SORTIE.
AVANT DE FERMER
-CAUTION-
HIGH TEMPERATURE AT
NOZZLE. RUN ON 'COLD'
BEFORE TURNING OFF.
Models, turn heat control to desired
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
heat setting). Heat
gun will come up
to full operating
temperature in
approximately two
minutes.
3. Adjustable stand
is provided to allow
nozzle to be rotated
from almost horizontal
to vertical position.
DU BEC OPÉRER À 'COLD' A LA SORTIE.
AVANT DE FERMER
-CAUTION-
HIGH TEMPERATURE AT
NOZZLE. RUN ON 'COLD'
BEFORE TURNING OFF.
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
4. To turn heat gun
off after use, move
switch to "I" position.
Run on cold for
approximately three
minutes. This will
allow the heat gun to cool down and the DU BEC OPÉRER À 'COLD' A LA SORTIE.
AVANT DE FERMER
-CAUTION-
HIGH TEMPERATURE AT
NOZZLE. RUN ON 'COLD'
BEFORE TURNING OFF.
nozzle to become cool to the touch. -ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
5. Move switch to
"O" position.
CLEANING
Unplug heat gun before cleaning. To clean
outside of tool, use only a mild soap and
damp cloth. Do not use other cleaning
agents, turpentine, gasoline, lacquer or paint
thinner, or other solvents that may contain
4
plastic bag, close it with tape or twist ties,
and dispose of properly.
• Remove protective clothing and work
shoes in the work area to avoid carrying
dust into the rest of the dwelling. Wash
work clothes separately. Wipe shoes off
with a wet rag that is then washed with
the work clothes. Wash hair and body
thoroughly with soap and water.
NOTICE: When heat gun is used in an
enclosed container, such as a shrink tunnel
or special enclosure, ambient air must be
allowed to pass into the heat gun and there
must be an outlet of equal size for the heated
air to pass out of the enclosure also. Total
enclosure will cause damage or possible
failure to the heat gun due to the extreme
heat generated.
For typical applications and tips please
consult www.masterappliance.com.
If you have any questions regarding your
specific application or use, feel free to call our
Customer Service Department at
(262) 633-7791.
NOTICE: Users should independently
evaluate the suitability of the product for
their application.
WARNING - To Reduce The Risk
Of Fire Or Electric Shock, Connect To
Grounded Outlet. Do Not Expose To
Rain Or Moisture. Store Indoors; Read
Instruction Manual Before Using.
CAUTION - HIGH TEMPERATURE
AT NOZZLE. RUN ON COLD BEFORE
TURNING OFF.
chemicals which are harmful to plastics and
other insulating materials. Never immerse
tool in a liquid or allow a liquid to enter inside
the tool. Make sure all vents and openings
are free and clear of debris.
www.masterappliance.com
Repair and Maintenance Instructions
SPECIfICATIONS
Size . . . . . . . . . . . 10"L x 5-1/4"W x 9-1/2"H
Nozzle opening . . . . . . . . . . . . .1-3/16" dia.
Nozzle shield length . . . . . . . . . . . 4-7/8" L
Average air velocity 3400 FPM at ambient
Master Heat Gun®
Master Heat Gun®
Temperature
Temperature
Model °F °C Voltage
Model °F °C Voltage
HG-201D/T 400 204
HG-201D/T 400 204
HG-301D/T 800 426
HG-301D/T 800 426
HG-501D/T 1200 649
HG-501D/T 1200 649
HG-801D* 1400 760
HG-801D* 1400 760
HG-202D/T 400 204
HG-202D/T 400 204
HG-302D/T 800 426
HG-302D/T 800 426
HG-502D/T 1200 649
HG-502D/T 1200 649
* Required 20A outlet, equipped with NEMA 5-20P Plug
* Required 20A outlet, equipped with NEMA 5-20P Plug
G
W
5-20P
Master Varitemp® Heat Gun
Master Varitemp® Heat Gun
Temperature
Temperature
Model °F °C Voltage
Model °F °C Voltage
VT-751D 100-1200 38-649
VT-751D 100-1200 38-649
VT-752D 100-1200 38-649
VT-752D 100-1200 38-649
REPAIR AND MAINTENANCE INSTRUCTIONS
All repairs and maintenance must be
performed by a qualified repair technician
who is experienced with the repair of electric
tools, a qualified service organization, or
Master Appliance Corp.'s Repair Department.
Please contact Master's Customer Service
Department for genuine Master Appliance
replacement parts or for repair service.
MASTER HEAT GUN® REPLACEMENT PARTS (HG/VT MODELS)
Master Heat Gun® replacement parts
and accessories are engineered and
manufactured to precise MASTER
APPLIANCE specification. Replacement
parts and accessories from other
manufacturers are not produced to these
precise specifications and therefor may
Important Safety Information • Read all safety information before operating
equipment. Save these instructions
www.masterappliance.com
Average air volume . . . 27 CFM at ambient
Net weight (with stand) 3.7 lbs. (D-models)
. . . . . . . . . . . . . . . . . . . . 2.8 lbs. (T-models)
Cord Length . . . . . . . . . . . . . . . . . . . .6 Ft. L
Replacement
Amps Watts Element
Replacement
Amps Watts Element
120 5 600 30087
120 5 600 30087
120 12 1440 30085
120 12 1440 30085
120 14.5 1740 30083
120 14.5 1740 30083
120 18.5 2220 30082
120 18.5 2220 30082
220 3 660 30088
220 3 660 30088
220 6 1320 30086
220 6 1320 30086
220 9 1980 30084
220 9 1980 30084
Replacement
Amps Watts Element
Replacement
Amps Watts Element
120 14.5 1740 30083
120 14.5 1740 30083
220 9 1980 30084
220 9 1980 30084
Master Appliance Corp.
262-633-7791
sales@masterappliance.com
www.masterappliance.com
WARNING: Always unplug your
tool before performing any maintenance
or repairs. Use only identical Master
Appliance brand replacement parts.
cause difficulties with or actually cause
damage to your Master Heat Gun®. Master
Appliance cannot assume responsibility
or liability for difficulties or damage
resulting from the use of any other brand of
replacement parts or accessories with your
Master Heat Gun®.
5