Publicité
ECO mode
RO/RT
The heat generated in the device can be reduced by lowering the
power of the input coils.
Pressing the "ECO Mode" (F) key to reduce the current power
setting. ECO mode is indicated by an "E" preceding the speed.
When the power is set to ECO mode, the speed is limited to 600
rpm.
Operating modes
RO/RT
To toggle between modes, press the Start/Stop key (C) when
switching on.
Operating Mode "A"
All the parameter settings are retained when the device is
switched off or disconnected from the mains.
The "Start/Stop" (C) key starts the device with the set parameters.
Operating Mode "B"
All parameter settings, including "Start/Stop", are saved when the
device is switched off.
Direction of rotation reversal
RO/RT
The (G) key activates the "Reverse Rotation" function.
When the „Reverse Rotation" function is switched on, a decimal
point (K) appears in the LCD display.
The running time (30, 60, 90 or 120sec) is set by pressing the (G)
key followed by the +/- keys.
After the preset running time, the drive is switched off and
restarted at minimum speed in the opposite direction after a
pause specific to the speed.
Function Heating
RT
The heating function is started and stopped by pressing the
„Temp" button (J).
Maintenance and cleaning
The equipment is maintenance-free. It is only subject to the natu-
ral wear and tear of components and their statistical failure rate.
Cleaning
- For cleaning disconnect the mains plug!
- Use only cleaning agents which have been approved by IKA to
clean the devices:
These are: water (containing surfactant) and isopropyl alcohol.
12
To make the stirring power more independent from the speed
range, press the "ECO Mode" membrane key (F) and then select
one of the following setting options.
P50 (Stirring power 50% independent of the speed range)
P75 (Stirring power 75% independent of the speed range)
P100 (Stirring power 100% independent of the speed range)
----
(Standard stirring performance with the stirring power
regulated by the speed)
Operating Mode "D"
In the D mode the device operates as per the A mode but with the
following exception:
- Switch on and then press the "Temp" membrane key to confirm
the safety temperature.
- The value flashes until it is confirmed.
Factory setting: mode A
In this way the magnetic rod is captured and any liquid still
rotating is gradually slowed down. Then the drive accelerates to
the target speed.
Note: If the "Reverse Rotation" key (G) is pressed again, the drive
will keep rotating in the same direction.
When the device is started up again, the drive will rotate in the
direction last set.
Pressing the +/- buttons (H or I) increases or reduces the
temperature.
- Wear protective gloves during cleaning the devices.
- Electrical devices may not be placed in the cleansing agent for
the purpose of cleaning.
- Do not allow moisture to get into the device when cleaning.
- Before using another than the recommended method for
cleaning or decontamination, the user must ascertain with IKA
that this method does not destroy the device.
Ordering spare parts
When ordering spare parts, please give:
- Device type
- Manufacturing number, see type plate
- Software version
- Item number and designation of the spare part,
see www.ika.com.
Error Codes (RT 5/10/15)
Error code
Cause
Effect
Er03
Temperature inside device is too high
Heating off
Er21
Safety relay doesn't open during test
Heating off
Er22
Safety temperature is too low during
Heating off
test
Er25
Heating and switching element
Heating off
monitoring
Er26
Difference between temperature of
Heating off
safety sensor and temperature of
control sensor: control temperature
> (safety temperature + 40 K)
Er31
Triac error detection doesn't work
Heating off
Er46
Difference between temperature of
Heating off
safety sensor and temperature of
control sensor: safety temperature
> (control temperature + 40 K)
If the actions described fail to resolve the fault or another error code is displayed then take one of the following steps:
- Please contact the service department;
- Send the device for repair, including a short description of the fault.
Accessories
• Stirring bar:
ø 8 mm; length 30 mm
• RSE
Stirring bar remover
Repair
Please send instrument in for repair only after it has been
cleaned and is free from any materials which may consti-
tute a health hazard.
For this you should request the "Safety Declaration (Deconta-
mination Certificate)" from IKA, or use the download printout
of it from the IKA website www.ika.com.
Return the instrument in its original packaging. Storage packaging
is not sufficient. Also, please use suitable shipping package mate-
rials.
Solution
- Switch off device and allow to cool down
- Switch off device
- Warning! Only to be carried out by authorised service personnel:
Check PCB
- Switch off device
- Warning! Only to be carried out by authorised service personnel:
Check PCB and safety temperature sensor
- Check the external temperature controller
- Switch off device
- Warning! Only to be carried out by authorised service personnel: Carry
out an internal test on the device to check the plug-in connector for
the heating element, the safety temperature sensor or the PCB
- Switch off device
- Warning! Only to be carried out by authorised service personnel: Carry
out an internal test on the device to check the plug-in connector for
the temperature sensor
- Switch off device
- Warning! Only to be carried out by authorised service personnel:
Check PCB
- Switch off device
- Warning! Only to be carried out by authorised service personnel:
Carry out an internal test on the device to check the plug-in connec-
tor for the temperature sensor
13
Publicité
