Publicité
Les langues disponibles
Les langues disponibles
Tilting the circular saw blade beyond
the left 0° - 45°
1.
Rotate the lever counterclockwise.
2.
Hold the handle and set the carriage at 0° for right
2° side, or 45° for left 47° side.
3.
Tilt the carriage slightly to opposite side.
4.
Push the releasing button.
5.
Tilt the carriage to the desired position beyond the
range 0° - 45°.
6.
Tighten the lever clockwise to secure the arm.
When tilting the carriage to the right 2°
► Fig.20: 1. Lever 2. Handle 3. Releasing button
When tilting the carriage to the left 47°
► Fig.21: 1. Lever 2. Handle 3. Releasing button
Switch action
Before plugging in the tool,
WARNING:
always check to see that the switch trigger actu-
ates properly and returns to the "OFF" position
when released. Do not pull the switch trigger hard
without pressing in the lock-off button. This can
cause switch breakage. Operating a tool with a
switch that does not actuate properly can lead to loss
of control and serious personal injury.
NEVER use tool without a fully
WARNING:
operative switch trigger. Any tool with an inoper-
ative switch is HIGHLY DANGEROUS and must be
repaired before further usage or serious personal
injury may occur.
NEVER defeat the lock-off button
WARNING:
by taping down or some other means. A switch with
a negated lock-off button may result in unintentional
operation and serious personal injury.
WARNING:
NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-off button. A switch in need of repair
may result in unintentional operation and serious
personal injury. Return tool to a Makita service center
for proper repairs BEFORE further usage.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
A hole is provided in the switch trigger for insertion of a
padlock to lock the tool off.
► Fig.22: 1. Switch trigger 2. Lock-off button 3. Hole
for padlock
WARNING:
Do not use a lock with a shank
or cable any smaller than 6.35 mm in diameter. A
smaller shank or cable may not properly lock the tool
in the off position and unintentional operation may
occur resulting in serious personal injury.
Casting a cutting line
CAUTION:
The lamp is not a rainproof. Do not
wash the lamp in water or use it in a rain or a wet
area. Such a conduct can cause an electric shock
and fume.
CAUTION:
Do not touch the lens of the lamp
as it is very hot while it is lighted or shortly after it
is turned off. This may cause burns.
Do not apply impact to the lamp,
CAUTION:
which may cause damage or shortened service
time to it.
CAUTION:
Do not look in the light or see the
source of light directly.
The LED lamp casts a light over the circular saw blade,
and a shadow of the saw blade falls onto a workpiece
serving as a calibration-free cutting line indicator. Press
the lamp switch to shed a light. A line appears in which
the saw blade will meet the surface of the workpiece,
becoming deepened as the saw blade gets lowered.
► Fig.23: 1. Lamp switch 2. Lamp 3. Cutting line
The indicator helps cut through an existing cut-off line
penciled on a workpiece.
1.
Hold the handle and lower the circular saw blade
so a dense shadow of the saw blade is thrown against a
workpiece.
Align a cut-off line drawn on the workpiece with
2.
the shadowed cutting line.
Adjust the miter angles and bevel angles if
3.
necessary.
NOTE: Be sure to turn off the lamp switch after use.
Otherwise the lamp stays hot.
Electronic function
Soft start feature
This function allows the smooth start-up of the tool by
limiting the start-up torque.
ASSEMBLY
WARNING:
switched off and unplugged before working on
the tool. Failure to switch off and unplug the tool may
result in serious personal injury.
Hex wrench storage
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
► Fig.24: 1. Hex wrench
20 ENGLISH
Always be sure that the tool is
Publicité
