IBEA 40 L/B/MUL Manuel D'instruction page 24

GB
ENGLISH
ENGINE / TRANSMISSION ASSEMBLY
Fig. 2 - Connect the engine (B) to the transmission (A) by
means the screw (C).
Make sure that the drive shaft and the tube are pulled
into the sleeve to the end.
FITTING THE THROTTLE CABLE AND STOP SWITCH
WIRES Fig.3
- Remove the filter cover
- Introduce the throttle cable (A) through of the cable tensioner
(B). Make sure that the cable sheath (C) rest against the
inside of the tensioner (B). Ensure that the throttle lever is
not in half-throttle, then connect the cable terminal in the
clamp (E). Adjust cable tension (A) by loosening the lock
nut (D) and turning the tensioner (B). Once the correct tension
is reached, tighten the lock nut (D). lf adjusted correctly,
throttle trigger will move freely approximately 2 mm before
carburettor lever (E) moves. Connect the stop switch wires
(F- G).
FITTING THE HANDLE BICYCLE (B) - (BT) AND LOOP (L)
TYPE
Fig. 4 (mod. L) - Remove the screws (1) open the loop handle
(2) in order to slip it on to the tube (3) and secure it by means
the screws (1) and the nuts (4). Fit the safety bar (5) into it's
seat and secure it by means the screws (6) and nut (7).
The position of the handle could be adjusted according with
the requirements of the operator.
Fig. 5 (mod. B) - Fit two half-handles (1-2) on the bracket
(D). Make sure the ends of the half handles are located into
the groove (4), see the arrow, and secure them using the
cover (5), screws (6) and nuts (7).
ASSEMBLY SAFETY GUARD Fig. 7
Mount the total protection (A + H) on the transmission
pipe (B) and secure using the jumper (C), screws (D),
piatrina (G) and nuts (F).
IMPORTANT: Make sure the jumper (C) is fixed to
the conical torque (L) through the screw and
washer (E). CAUTION: Use protection (A + H) with the
head of a nylon wire. Use only the protection (A) with the
lame.Per reasons of safety, the saw blades can not be
used with no protection provided.
BLADE ASSEMBLY (4) Fig. 8-9
- Loosen the nut (1) clockwise; remove cup (2) (only if is the
skid unit version) and lower flange (3).
- Fit the blade (4) as showed in the picture making sure that
the upper flange (5) is well fitted.
- Fit the blade making sure that the rotation direction is correct
(the inscription on the blade should be facing up).
- Fit the lower flange (3), the cup (2) (only if is the skid unit
version) tighten the nut (1) anti-clockwise at 30 Nm ( 3.0
kgm).
5. ASSEMBLY
- While tightening the nuts (1), the blade can be held fast by
inserting the allen key Ø 4 mm into the cap, the upper flange
and gear case holes. To do this, rotate the cutiing tool until
the two holes coincide.
NYLON HEAD ASSEMBLY (2) Fig. 10-11
Mount the head of a nylon wire following the Illustrated:
upper flange (1) and turn clockwise to the head of nylon
threads.
Tighten by hand clockwise head as shown in Fig.10 after
entering the Allen key (4 mm) in the conical bore of the
pair.
For your safety, use only original cutting tools.
WARNING: ONLY FOR EVOLUTION MODELS
FITTING THE ATTACHMENTS Fig. 25
Loose, counter-clockwise, the lever (1).
- Pull up the pin (12) and slip the tube (2) into the coupling (4)
as far as the reference (3) (about 40mm.). In order to ease
the introduction of the inner shaft (5) into the coupling shaft
(6), twisting slightly one way and the other the attachment
till it is slipped to the ref. (3).
Make sure that the pin (12) is inserted into the hole (13).
Block the tube through the lever (1)
FITTING THE EXTENSION
Fitting extension / machine Fig. 26
- Loosen, counter-clockwise, the lever (1).
- To slip the extension tube (2) into the coupling (4) as far as
the reference (3) (about 40mm.). Rotate the extension in order
to locate the coupling (10) in the same position as the coupling
(4) and secure it by the lever (1).
Fitting attachment / extension Fig. 26
- loosen, counter-clockwise, the lever (7).
- To slip the attachment tube (8) into the coupling (10) as far
as the reference (9) (about 40mm.) In order to introduce the
shaft (11) with ease into the extension coupling shaft, twist
slightly one way and the other the attachment, till the tube is
fully introduced.Rotate the attachment in the working position
and secure it by the lever (7).
WARNING: to use the attachments see the specific
owner's manual.
The maximum extension allowed is 1.500mm.,
otherwise it is dangerous. Only one extension each time
can be used on the machine, the 750mm. or alternatively
the 1.500mm.
24