R&G CP0334BL Instructions De Montage page 5

Coté droit (assis sur la moto)

Enlever les 2 boulons (Photo 5).

Placer 2 des entretoises (Article 8) dans les contre alésages (Photo 6).
Page | 10

Monter le bloc de montage (Article 9) (Photo 7) en utilisant 2 des boulons à tête en
capuchons (Article 6) sans excéder 25Nm de couple.

Placer une rondelle M10 (Article 3) sur un des boulons M10 (Article 2).

Placer une des Rondelles Shake Proof M12 (Article 4) autour du boulon (de façon à ce qu'elle
se place contre la rondelle qui vient d'être insérée.

Placer le boulon avec rondelles à travers une des protections crash (de façon à ce qu'il aille
dans le contre alésage).

Placer l'ensemble dans le bloc de montage.

Serrer le boulon avec une clé de 17mm jusqu'à ce que vous sentiez une légère compression
de l'intérieur de la protection. LA PROTECTION DOIT ETRE POSITIONNEE COMME EN "C"
AVEC LE COTE ARRONDI LE PLUS GROS EN DIRECTION DE L'AVANT DE LA MOTO. Tourner
un peu plus afin d'accentuer légèrement la compression. Ne pas trop serrer, au risqué
d'abîmer la moto. Pas plus de 40 Nm de couple.

Mettre les capuchons aux protections (Article 1) (Photos A et B).
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not
refer to faulty goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
Unit 1 Shelleys Lane, East Worldham, Alton, Hants GU34 3AQ
18/01/2013 (NSY)
www.rg-racing.com Email: info@rg-racing.com