Publicité
LEGENDE
ARTICLE 1 = M6 x 65mm BOULON (x1).
ARTICLE 2 = BOBINE (B0481) (x2).
ARTICLE 3 = BLOC DE FIXATION COTE GAUCHE (M0501) (x1).
ARTICLE 4 = ECROU CONIQUE (H0015) (x2).
ARTICLE 5 = BLOC DE MONTAGE DROIT (M0354) (x1).
ARTICLE 6 = M6 x 40mm BOULON (x1).
NOTICE DE MONTAGE
Coté gauche (assis sur la moto)
•
Insérer le boulon (article 1) dans la protection crash de façon à ce que la tête se place dans le
contre alésage.
•
Placer la bobine sur le bloc de fixation plus large (article 3 – M0501).
•
Placer l'écrou conique (article 4 – H0015) sur l'extrémité du boulon de façon à ce que la face
conique se place dans le creux du bloc de fixation.
•
Serrer le boulon jusqu'à ce que la portion conique de l'écrou entre en contact avec le creux du bloc
de fixation.
•
Placer cet ensemble du côté gauche de l'axe de roue arrière, avec le profile plat usiné espacé du
patron relevé sur le bloc d'ajusteur de chaine.
•
Serrer le boulon de façon à ce que la bobine soi correctement fixée en position (ne pas trop serrer).
Coté droit (assis sur la moto)
•
Insérer le boulon plus court (article 7) dans la protection crash de façon à ce que la tête se place
dans le contre alésage.
•
Placer la bobine restante sur le bloc de fixation plus petit (article 5 – M0354).
•
Placer l'écrou conique (article 4 – H0015) sur l'extrémité du boulon de façon à ce que la face
conique se place dans le creux du bloc de fixation.
•
Serrer le boulon jusqu'à ce que la portion conique de l'écrou entre en contact avec le creux du bloc
de fixation.
•
Placer cet ensemble du côté droit de l'axe de roue arrière.
•
Serrer le boulon de façon à ce que la bobine soi correctement fixée en position (ne pas trop serrer).
•
Vérifier régulièrement le serrage de la bobine.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall
at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained
otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These
terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G
Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
OUTIL REQUIS
•
Clé Allen 4mm.
ISSUE 1 12/05/2017 (AR)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
