JANE JET NURSE Mode D'emploi page 11

GB
jet
3_ Pull out the shoulder straps and place them on both sides of the seat.
4_ When i-size (40-105cm) is used by children, please refer to the above picture description for the shoulder
strap.
5_ Pull and adjust the safety belt outward to make the shoulder belt effectively restrain the children, and
reserve a certain space to prevent the child seat belt from pressing the children too much. The adult palm
can be inserted just between the safety belt and the children's chest. It is better not to be loose or tight, and
ensure that the pelvis area can be well restrained when the belt is worn.Note: The bottom of both sides of
the shoulder shield should be close to the same level and pulled down to the bottom.
6_ How to use the buckle: put the buckle insert around and together, and then insert the buckle slot at the
same time. The sound of clicking indicates that the buckle has been stuck.Then pull up the clip insert to
check whether the clip is properly locked.To unfasten the clasp, press the red button and the clasp insert will
pop out automatically.
7_ Pull the headrest handle upward to adjust the height of the headrest. Adjust the height to the right
position according to the different heights of the child.
8_ After the baby is seated, adjust the head to the right position (note: the lowest part of the head is 1-2
fingers away from the shoulder is the best).
9
9. FIVE-POINT SAFETY BELT CONCEALMENT
1_ Shoulder guard separation: open the shoulder guard, separate the connector from the shoulder belt, pull
out the shoulder guard, and keep the shoulder guard for future use.
2_ Open the buckle as shown in the picture, adjust the safety belt to the longest, open the cloth cover, put
the buckle insert into the grooves on both sides, and then put the buckle insert into the groove under the
cloth cover and seat cushion.
3_ After the five-point safety belt is hidden, it depends on whether the head can be adjusted.Finally, please
put away the important parts after the demolition.The effect diagram of the back and front of the finished
seat is shown above.
10
10. 100-150cm:
1. ISOFIX ATTACHMENTS+ADULT SAFETY-BELT
2. ADULT SAFETY-BELT
Attention
A_ his ECRS seat is installed forward and suitable for children with height of 100-150cm. Only one seat can be
adjusted as the second position.
B_ Hide the five-point safety belt and pad before using the ECRS seat.
C_ Suitable for models with ISOFIX systems which pass ECE R14 and with three-point seat belt/seat belt with
a retractor which pass ECE R16.
D_ Don t use force-bearing points without marking.
E_ When using forward, please remove the backward protection system.It is not suitable for cars with only
two point seat belts.
ISOFIX ATTACHMENTS+ADULT SAFE-BELT
10
.1
1_ Please rotate the seat to the forward state first and then pull the handle. Then shift the sitting position to
the second position and shrink the top tether to the shortest.
2_ Press the ISOFIX button at the bottom of the seat forward and backward with your hand, push the ISOFIX
on both sides to the maximum, press the end of the ISOFIX, and it will not be retracted.
3_Insert the ISOFIX of the baby safety seat into the corresponding ISOFIX fixed point of the car, and a click
will be heard to display green in the display window.It will display red in the window before ISOFIX inserted
correctly.
4_ Push the baby car seat to the back of the car seat to make them fit tightly. Shake the seat from side to side
to make sure it is effectively fixed.
20
GB
jet
ADULT SAFETY-BELT
A_ Step five: Settle the child in the car seat, adjust the headrest to the right position, place the upper end of
the car seat belt diagonally through the guide hook slot at the bottom of the head, the lower end of the
diagonal band passes through the corresponding guide mark, the cross band passes through two left and
right guides, finally, the car seat belt clasp is attached to the seat belt buckle, you will hear the click when
it is securely fastened, the child's pelvis should be held firmly when the belt is worn.
Don t use force-bearing points without marking
11 11. REMOVING THE COVER
1_ Removal of headrest cloth cover: Headrest cloth cover can be removed by releasing rubber band.
Remove chair body cloth cover:open the two sides of the chair and the four button on the two
sides of the head, and then cover on the chair can be removed
12. MAINTENANCE
12
Store the harness away and remove the padding.
Take the fabric cover off the headrest.
Unfasten the button and remove the fabric cover from the lower part of the headrest.
To fit the fabric cover again, follow the same steps in reverse order.
The safety lock is not working properly if the following situations occur:
1) When you press the red button it opens slowly
2) It is not possible to insert the metal parts of the safety lock into the fastener or, when they are inserted they
automatically come loose again.
3) The safety button does not emit the safety click.
4) It is difficult to insert the metal parts into the safety lock.
5) Excessive force is required to open the safety lock.
The 5-point safety harness is very important for the child's safety. Incorrect use of the 5-point harness may put
the child's safety at risk. Do not use oils or other lubricants on the safety lock. Defects in the functioning of the
safety lock are usually caused by inserting foreign objects into the lock.
13 13. RECOMMENDATIONS
Check all the parts of the safety seat before using it. Make sure that it is in good condition as this will reduce
the risk of an accident.
Check that the seat belts are not too loose before use.
Do not expose the safety seat to excessively cold or hot temperatures, or damp environments.
Keep the instruction manual in a safe place.
In the event of an accident replace the car seat with a new one. Contact your retailer if you have any questions.
14. GUARANTEE INFORMATION
14
- This item is guaranteed against manufacturing defects as stipulated in the legal Directives and/or regulations
in force on guarantees for consumer goods applicable to the European Union and those of the country in which
it is marketed.
- It is essential to present the purchase invoice or receipt in order to process the guarantee through the seller
of the item or, failing that, through the manufacturer.
- The guarantee excludes anomalies or faults caused by misuse, non-compliance with the safety regulations
and instructions for use and maintenance provided, or due to wear and tear caused by normal use and regular
handling of the item.
- The label containing the serial number of your model must not be torn off under any circumstances as it
contains information relevant to the guarantee.
21