Simons Voss Technologies Digital Cylinder AX Guide Abrégé page 42

4. Extend Cylinder AX
Double cam Cam gear, 10 teeth
Z5.CAM.DOUBLE Z5.CAM.GEAR10
 
3.3 Tools
Various tools are available to adjust the Digital Cylinder AX:
Lifter (Z5.LIFTER) Spacer (Z5.SPACER)
The Digital Cylinder AX thumb turn installation tool is designed so that you
can use it to hold the Digital Cylinder AX in place. Position it with the flat side
on a flat surface and place the Digital Cylinder AX together with the thumb-
turn in the installation tool. Reassembly is easier when the Digital Cylinder AX
is in the holder.
2
4. Extend Cylinder AX
3
The core extension and profile extension must be the same length. You also
need an extension bolt for the desired length.
ü Extractor for releasing the clamp
ü Spacer for aligning the extension bolt
ü Clamp block for pressing in the clamp
1. Place the Cylinder AX in the thumb-turn assembly tool.
4
2. Hook the tip of the extractor into the clamp.
5
3. Lever the clamp out of the profile cylinder by moving the extractor to
the centre of the cylinder.
6
4. Pull the clamp completely out of the profile cylinder.
7
5. Disassemble the two cylinder halves.
8
6. Use the extractor to unscrew the extension bolt.
9
7. Insert suitable core extensions.
8. Attach suitable profile extensions.
10
9. Place the spacer.
11
10. Screw in a suitable extension bolt with the extractor until it rests on the
spacer.
NOTE
Length on bolt head
You will find a number on the bolt head. This number is the length of the cyl-
inder profile to which the bolt fits.
42 / 76
Cam gear, 18 teeth
11.
12.
13.
Z5.GEAR.18

14. Place the clip back into the slot of the profile cylinder with its lug facing
Terminal block
(Z5.BLOCK)
15.
16. Push the clamp block lever towards the base plate until the clamp is
9
5. Shorten Cylinder AX
You need a bolt for the desired length.
ü
ü
ü
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Screw in a suitable bolt with the extractor until it rests on the spacer.
Length on bolt head
You will find a number on the bolt head. This number is the length of the cyl-
inder profile to which the bolt fits.
11.
Digital Cylinder AX (Z5) Modularity
12
Reassemble the two cylinder halves.
13
Extension bolt is protected against twisting.
9
Pull the spacer off again.
14
Push the halves together completely.
15
the fastening screw and press the clamp with your thumb so that it can
no longer fall out.
16
Insert the cylinder into the clamping block so that the profile cylinder
and the thumb-turn lie flush in the recesses.
17
9 The lever of the clamping block is reinforced at one point with a
metal plate. The bracket that was previously inserted lies opposite
this metal plate.
fully seated in the profile cylinder.
Cylinder AX is extended.
18
Extractor for releasing the clamp
Spacer for aligning the bolt
Clamp block for pressing in the clamp
Place the Cylinder AX in the thumb-turn assembly tool.
19
Hook the tip of the extractor into the clamp.
20
Lever the clamp out of the profile cylinder by moving the extractor to
the centre of the cylinder.
21
Pull the clamp completely out of the profile cylinder.
22
Disassemble the two cylinder halves.
23
Unscrew the bolt with the extractor.
24
Remove the profile extension.
Remove the core extension.
25
Place the spacer.
26
NOTE
27
Reassemble the two cylinder halves.
28
EN