Publicité
Les langues disponibles
Les langues disponibles
EN
Note: When cutting with the table at an angle other than 90° to the blade, always use the Fence
(20) on the lower side of the table.
• For general cutting, follow the pattern lines by pushing and turning the workpiece at the same
time
• To achieve a curved radius cut, follow the pattern line with the blade while turning the workpiece.
The blade should cut in the middle of the pattern line
• Use both hands to feed the work through the blade
• Make sure you hold the workpiece firmly against the work table
• Use light forward pressure and do not force the workpiece against the bandsaw table
• When cutting small workpieces that have insufficient area to hold, or do not protrude over the
edge of the Work Table (15), use the provided push-stick to feed the workpiece into the blade
Note:
Always keep the push-stick nearby, so that it is readily available for use whilst cutting and
keep the push-stick away from the any conflict with blade.
Accessories
• A range of accessories and consumables, including 6tpi (633924), 10tpi (868739), and 14tpi
(675295) Bandsaw blades, are available from your Silverline stockist. Spare parts can be
obtained from toolsparesonline.com
Maintenance
WARNING:
ALWAYS disconnect from the power supply before carrying out any inspection,
maintenance or cleaning.
WARNING:
DO NOT attempt to modify this tool or create accessories not recommended for
use with this tool. Any such alteration or modification is a misuse and could result in a hazardous
situation, leading to possible serious personal injury.
Replacing the blade
Note:
Always use a saw blade that is compatible with the type of material being cut, for most
effective, and efficient cutting.
Note: The blade length for this bandsaw is 1425mm (56 1⁄ 4 ").
1. Unscrew the Upper Cover Knob (2) and Lower Cover Knob (7) of the hinged housing cover, to
reveal the internal bandsaw mechanism (Fig. IX)
2. Loosen the Blade Guard Adjusting Knob (14) and position the Blade Guard (3) halfway above the
table. Tighten the Blade Guard Adjusting Knob (14)
3. Loosen the two blade guard mounting screws (Fig. X) with a hex key and remove the Blade Guard
(3)
4. Remove the Table Aligning Screw (6) from the work table (Fig. I)
5. Turn the Blade Tension Adjustment Knob (12) anti-clockwise to release blade tension and remove
the old blade
6. Slide the old blade off the upper and lower Blade Wheels, and through the table slot
7. Guide the new blade through the blade slot, (Fig. III) and on to the Blade Wheels. Ensure that the
blade is pointing outwards, with the teeth facing downwards (Fig. XI)
8. Centre the blade on the soft, non-slip surface of the upper and lower Blade Wheels, see 'Blade
tracking' for detailed instructions on blade alignment
9. Rotate the wheels clockwise to help guide and centre the blade on the blade wheels
Replacing the table insert
• When worn, the table insert can be removed and replaced
• To remove the table insert, remove the Phillips head screw securing the table insert to the Work
Table (15). Then remove and replace
Wheel brush
• The wheel brush is located inside the housing (Fig. XV) and helps keep the blade and the wheel
free of sawdust and wood chips
• To adjust, loosen the screw and position the wheel brush so that it contacts the bristles of the
brush
• Retighten the screw
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised Silverline service centre. This advice also applies to extension cords
used with this tool
EN
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the machine's service life. Clean the body of your machine with a soft brush, or dry cloth.
If available, use clean, dry, compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do not use alcohol, petrol
or strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: www.silverlinetools.com
UK Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
EU Address:
Toolstream B.V.
Holtum-Noordweg 11
Unit 46121 RE Born
The Netherlands
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools
Publicité
