Publicité
Les langues disponibles
Les langues disponibles
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the recommended
tools and parts before starting
installation. Read and follow the instructions provided with any tools
listed here.
All Installations
Tools needed:
Phillips
screwdriver
Flat-blade
screwdriver
Utility: knife
Se" and Va"
nut drivers or
hex sockets
UL Listed/CSA
Approved twist-on{]
wire connectors*
Measuring tape
g
10" adjustable wrench
J
that opens to
:
1%" (2.9 cm)
54" open-end
wrench
*Must be the proper size to connect your household wiring to
16 gauge wiring in dishwasher
Other useful items
you may
need:
Flashlight
Bath towel
Shallow-pan
Wood block
Z
Parts supplied:
Drain hose clamps (2)
Drain hose
#10.x 1%"
(1Jarge and 1 small)
Phillips-head
screws
Silver
Make sure all these parts are included in the literature package.
Parts needed:
¥" Compr. x 34° Hose Fitting]
For part-or-kit, see local
retailer or call Whirlpool
Parts: 1-800-442-9991, Part
Number W10273460
EZ
Ss
oe /
Other parts you may also need:
Tyt—2"
Side mounting kit -| Masking or
(38.1=5 cm)
for solid surface
duct tape
Screw-type
countertops
:
(Part Number
clamps (3 maximum)
3212560)
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See "Electrical
Requirements" section. It is recommended that electrical connections be
made by a licensed electrical installer.
In addition, for first time installations
Tools needed:
Cordless drill
with", 34"
and 114" hole
saw. bits
Small
tubing cutter
Wire stripper
Parts needed:
Copper tubing (3"
O.D. suggested) or
flexible braided
water supply line
See "Electrical Requirements" section
For Direct Wire:
use UL Listed/
CSA Approved
strain relief
to fit #". (2.2 cm)
hole
For-Power Supply
Cord:-use UL
Listed power.
supply-cord kit
marked for-use
with dishwasher
Location Requirements
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between
motor and flooring. Motor should not
touch the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by the
warranty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277)
is available
from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The
location must provide:
- easy access to water, electricity and drain.
- Convenient access for loading and unloading dishes. Corner
locations require a 2" (5.1 cm) minimum
clearance between the
side of the dishwasher door and the wall or cabinet.
- square opening for proper operation and appearance.
- cabinet front perpendicular to floor.
- level floor. (If floor at front of opening
is not level with floor at
rear of opening, shims may be needed to level dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the dishwasher
opening is uneven (example: flooring extends only partway into
opening).
NOTE: To avoid shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or ina
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown
in the "Product and Cabinet Opening
Dimensions" section.
Publicité
