Publicité
CAUTION:
• KEEP FOREIGN OBJECTS OUT OF THE
HOPPER.
• THE MOVING PARTS OF THIS STOVE ARE
PROPELLED BY HIGH TORQUE ELECTRIC
MOTORS. KEEP ALL BODY PARTS AWAY
FROM THE AUGER WHILE THE STOVE IS
PLUGGED INTO AN ELECTRICAL OUTLET.
THESE MOVING PARTS MAY BEGIN TO
MOVE AT ANY TIME WHILE THE STOVE IS
PLUGGED IN.
PRE-START-UP CHECK
Remove burn pot, making sure it is clean and none
of the air holes are plugged. Clean the firebox, and
then reinstall burn pot. Clean door glass if necessary
(a dry cloth or paper towel is usually sufficient).
Never use abrasive cleaners on the glass or door.
Check fuel in the hopper, and refill if necessary.
BUILDING A FIRE
Never use a grate or other means of supporting
the fuel. Use only the burn pot supplied with this
heater. Hopper lid must be closed in order for the
unit to feed pellets. During the start-up period:
• Make sure the burn pot is free of pellets.
• DO NOT open the viewing door.
• DO NOT add pellets to the burn pot by hand.
NOTE: During the first few fires, your stove will
emit an odor as the high-temperature paint cures
or becomes seasoned to the metal. Maintaining
smaller fires will minimize this. Avoid placing items
on the stovetop during this period because the paint
could be affected. Attempts to achieve heat output
rates that exceed heater design specifications can
result in permanent damage to the heater.
OPTIMAL OPERATION
This pellet stove has been certified by the US EPA
to meet strict 2020 guidelines. To ensure this unit
produces the optimal minimal emissions, it is
critical to follow the following guidelines. To achieve
a "high burn", your stove should be set on setting 5
with the damper fully open. To achieve a "medium
burn", your stove should be set on setting 3 with the
damper closed 50%. To achieve a "low burn", your
stove should be set on setting 1 with the damper
fully closed. Setting 4 will give you a medium high
burn and setting 2 will give you a medium low burn.
© 2024 United States Stove Company
OPERATION INSTRUCTIONS
If the door is opened while the stove is in operation
it must be closed within 30 seconds or the stove
will shut down. If the stove shuts down push the
"On/Off" button to re-start your stove. The stove will
have to fully shut down and turn off before you will
be able to restart the stove
IGNITOR
1.
Fill the hopper and clean the burn pot. Fully
open the damper.
2. Press the "On/Off" button.
3. Set the heat range/temperature. Manual Mode
- Press the "Display Button" to see the current
heat range. Use the up and down arrows to
adjust the heat range. T-stat Mode - Press the
"Display Button" to see the current temperature
setting. Use the up and down arrows to adjust
the temperature as needed.
4. Adjust the damper for the desired burn rate
(see "OPTIMAL OPERATION").
If the fire doesn't start in 12 minutes, press "On/Off",
wait a few minutes, clear the burn pot, and start the
procedure again.
OPENING DOOR
• DO NOT OPERATE YOUR STOVE WITH
THE VIEWING DOOR OPEN. THE AUGER
WILL NOT FEED PELLETS UNDER THESE
CIRCUMSTANCES AND A SAFETY CONCERN
MAY ARISE FROM SPARKS OR FUMES
ENTERING THE ROOM.
• THE DOOR MUST BE CLOSED AND SEALED
DURING OPERATION.
If the door is opened while the stove is in operation
it must be closed within 30 seconds or the stove
will shut down. If the stove shuts down push the
"On/Off" button to re-start your stove. The stove will
have to fully shut down and turn off before you will
be able to restart the stove.
14
Open
CAUTION:
Closed
Publicité
