Mitsubishi Electric LGH-F470RVX-E Instructions D'installation page 17

Function settings (continued)
No.36
Outdoor temperature display setting
Set to display outdoor temperature detected by Lossnay unit
thermistor or not.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-61DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
N/A 36
- -
No.37
Indoor temperature display setting
Set to display indoor temperature detected by Lossnay unit thermistor
or not.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-61DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
N/A 37
- -
Calculated supply air temperature display
No.38
setting
Set to display calculated supply air temperature or not.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-61DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
N/A 38
- -
Temperature exchange efficiency
No.39, 40
setting
Set the 10 digit of temperature exchange efficiency which is used to
calculate supply air temperature.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-61DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
- -
N/A 39
- -
- -
- -
- -
- -
DIP-SW PZ-61DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
- -
N/A 40
- -
- -
- -
- -
- -
Setting Outdoor temperature
check display
0
N/A
(Factory setting)
Display on the screen of
1
PZ-61DR-E
Setting Indoor temperature
check display
0
N/A
(Factory setting)
Display on the screen of
1
PZ-61DR-E
Setting Calculated supply
check temperature display
0
N/A
(Factory setting)
Display on the screen of
1
PZ-61DR-E
Setting 10 digit of temperature
check exchange efficiency
0 0
1 1
2 2
3 3
4 4
5 5
6 6
7
7
(Factory setting)
8 8
9 9
Setting 1 digit of temperature
check exchange efficiency
0
0
(Factory setting)
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
No.41
Outdoor temperature correction
Set the correction for the outdoor temperature displayed on the
PZ-61DR-E screen by function No. 36
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-61DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
- -
- -
- -
N/A - - 41
- -
- -
- -
- -
- -
- -
- -
No.42
Indoor temperature correction
Set the correction for the indoor temperature displayed on the
PZ-61DR-E screen by function No. 37
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-61DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
- -
- -
- -
N/A - - 42
- -
- -
- -
- -
- -
- -
- -
No.51
Automatic ventilation mode setting
Set the pattern of conditions to go into By-pass mode in automatic
ventilation operation.
When setting Data is set "3" by PZ-61DR-E, function
and No. 54 are available.
DIP-SW PZ-61DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
OFF
(Factory setting)
SW2-7 51
ON
- -
* Pattern A is more likely to become By-pass mode than pattern B.
.
Setting The correction to
check thermistor detection
0 19 ˚F (-7 ˚C)
1 21 ˚F (-6 ˚C)
2 23 ˚F (-5 ˚C)
3 25 ˚F (-4 ˚C)
4 27 ˚F (-3 ˚C)
5 28 ˚F (-2 ˚C)
6 30 ˚F (-1 ˚C)
7
32 ˚F (0 ˚C)
(Factory setting)
8 34 ˚F (+1 ˚C)
9 36 ˚F (+2 ˚C)
10 38 ˚F (+3 ˚C)
11 40 ˚F (+4 ˚C)
12 41 ˚F (+5 ˚C)
13 43 ˚F (+6 ˚C)
14 45 ˚F (+7 ˚C)
.
Setting The correction to
check thermistor detection
0 19 ˚F (-7 ˚C)
1 21 ˚F (-6 ˚C)
2 23 ˚F (-5 ˚C)
3 25 ˚F (-4 ˚C)
4 27 ˚F (-3 ˚C)
5 28 ˚F (-2 ˚C)
6 30 ˚F (-1 ˚C)
7
32 ˚F (0 ˚C)
(Factory setting)
8 34 ˚F (+1 ˚C)
9 36 ˚F (+2 ˚C)
10 38 ˚F (+3 ˚C)
11 40 ˚F (+4 ˚C)
12 41 ˚F (+5 ˚C)
13 43 ˚F (+6 ˚C)
14 45 ˚F (+7 ˚C)
No. 52 , No. 53
Setting Conditions to go into
check By-pass mode
0
DIP-SW priority
(Factory setting)
Pattern A
Indoor temperature is 61 ˚F (16 ˚C) or more
1 Outdoor temperature is 61 ˚F (16 ˚C) or more
Indoor temperature - outdoor
temperature ≥ 32 ˚F (0 ˚C)
Pattern B
Indoor temperature is 72 ˚F (22 ˚C) or more
2 Outdoor temperature is 64 ˚F (18 ˚C) or more
Indoor temperature - outdoor
temperature ≥ 36 ˚F (2 ˚C)
3 Free setting
Eng-17
,