DITEC UP2-UP4 Manuel D'installation Et D'entretien page 10

1. TECHNICAL DATA
GB
Power supply
Motor power supply
Absorption
Torque
Capacitor
Opening time
Rod lenght (max)
Service class
Intermittence
Temperature
Degree of protection
Control Panel
2. REFERENCE TO ILLUSTRATIONS AND AC-
CESSORIES
The given operating and performance features can only be guar-
anteed with the use of DITEC accessories and safety devices.
2.1 Standard installation references (fi g. 1)
[1] Radio
[2] Flashing light
[3] Key selector
[4] Connect the power supply to an omnipolar switch with
contact opening distance of at least 3 mm (not supplied
by us) or by means of power plug.
Connection to supply mains must be carried out in an
independent raceway separate from control connections
and safety device connections.
[5] Barrier
[6] Photocells
2.2 Barrier references (fi g. 3, 4 and 8)
[7] Fixing base
[8] Container
[9] Rod holder attachment
[10] Key release
[11] Rod
[12] Geared motor
[13] Limit switch group (UP2E-UP4E)
[14] Encoder group (UP2EH-UP4EH)
[15] Transmission lever
[16] Internal mechanical lock
[17] Lever arm
[18] Top attachment for spring
[19] Spring
[20] Spring adjustment tie rod
[21] Control panel
[22] Screw TE M12x110 galvanized
[23] Upper spring coupling bracket
[24] Self-locking nut M12 galvanized
2.3 Accessories
UP2B Rectangular (30x60) net span arm 2500 mm for
UP2 barrieres
UP4BC Rectangular (30x100) net span arm 3500 mm
for UP4 barrieres
UP4BL Rectangular (30x100) net span arm 4500 mm for UP4
barrieres
UP4M Spring Ø 5 standard for UP4 barriers
UP4MP
Spring Ø 3,5
UP2-UP4 - IP1781
UP2E
230 V~ / 50 Hz
230 V~
1,2 A
45 Nm
8 µF
1,5 s/90°
2700 mm
5 - HEAVY DUTY
S2 = 60 min, S3 = 60% S2 = 60 min, S3 = 60% S2 = 15 min, S3 = 30% S2 = 60 min, S3 = 60%
-20° C / +55° C
IP45
E1A
UP2EH
230 V~ / 50-60 Hz
24V= with encoder
1 A
20 Nm
/
2÷3 s/90°
2700 mm
5 - HEAVY DUTY
-20° C / +55° C
IP45
73RU
UPC Set of 10 red refl ectors
UP4BAT Barrier battery kit for UP2EH-UP4EH
UPAF Fixed bearing
UPSN (*) Articulated joint for UP4BC/4BL arms
UPAM (*) Mobile bearing
UPGR (*) Aluminium fence L=2000 mm
(*) Attention: due to its high speed, the UP2 model cannot be
fi tted with accessories (UPGR,UPAM,UPSN).
3. INSTALLATION
Unless otherwise specifi ed, all measurements are expressed
in millimetres (mm)
3.1 Barrier installation
- Lay a concrete foundation with buried anchoring brackets
and the base plate, making sure that it is perfectly level and
smooth. Insert appropriate elements in iron or any other
suitable material into the holes of the anchoring hooks so
as to permit fi xing to the concrete reinforcement. (Fig. 3)
Route the cable ducts through the central hole of the plate.
Attention: ensure that anchoring is sturdy and stable.
- Fasten the group.
3.2 Reversal of the direction of the rod
The UP2-UP4 barriers are normally supplied in the right-hand
version. By right barrier we mean that the container is assem-
bled on the right, as seen from the side that can be inspected.
To transform the barrier from right to left:
- (Fig. 8) Disassemble the top attachment for spring: screw
[22], upper spring coupling bracket [23] and nut [24].
- Rotate the lever arm 90°.
- Disassemble the trasmission lever [15] from the lever arm
[17] and reassemble it with the top attachment for spring:
screw [22], upper sbring coupling bracket [23] and nut [24].
ATTENTION: Use the screw [22] and nut [24] of the upper
spring coupling to assemble.
- Move the control panel on the opposite side
- (Fig. 10) Position the DIP2 of the control panel on ON.
3.3 Arm installation
- Bring the rod bearing fl ange [9] to a vertical position. Lock
the geared motor (see operating instruction).
- (Fig. 4) Hook on the springs and the spring adjusting stud
bolt.
- (Fig. 5) Install the rod and secure it.
- Release the geared motor and position the rod horizontally.
10
UP4E
230 V~ / 50 Hz 230 V~ / 50-60 Hz
230 V~ 24V= with encoder
1,2 A
60 Nm
8 µF
3 s/90°
4700 mm
4 - INTENSIVE 5 - HEAVY DUTY
-20° C / +55° C -20° C / +55° C
IP45
E1A
UP4EH
1 A
45 Nm
/
2÷6 s/90°
4700 mm
IP45
73RU