Bosch AL 1814 CV Professional Notice Originale page 5

OBJ_BUCH-3344-001.book Page 5 Tuesday, November 28, 2017 9:06 AM
Technical Data
Battery Charger
Article number
Battery charging voltage (automatic
voltage detection)
Charging current
Allowable charging temperature
range
Number of battery cells
Weight according to EPTA-
Procedure 01:2014
Protection class
Charging time for battery
capacity, approx.
1.3 Ah–1.5 Ah min
2.0 Ah min
2.6 Ah–3.0 Ah min
4.0 Ah min
Operation
Starting Operation
 Observe the mains voltage! The voltage of the power
supply must correspond with the data given on the name-
plate of the battery charger. Battery chargers marked with
230 V can also be operated with 220 V.
Charging Procedure
The charging procedure starts as soon as the mains plug of
the battery charger is plugged into the socket outlet and the
battery 1 is inserted into the charging compartment 3.
Due to the intelligent charging method, the charging condi-
tion of the battery is automatically detected and the battery is
charged with the optimum charging current, depending on
battery temperature and voltage.
This gives longer life to the battery and always leaves it fully
charged when kept in the charger for storage.
Note: The charging procedure is only possible when the bat-
tery temperature is within the allowable charging tempera-
ture range, see "Technical Data" section.
Meaning of the Indication Elements
Flashing Battery Charge Indicator 2
The charging procedure is signalled by a
flashing battery charge indicator 2.
Continuous Lighting of the Battery Charge Indicator 2
Continuous lighting of the battery
charge indicator 2 indicates that the
battery is fully charged or that the
temperature of the battery is not with-
in the allowable charging temperature range, and cannot be
Bosch Power Tools
charged for this reason. The battery is charged as soon as the
allowable charging temperature range is reached.
AL 1814 CV
When the battery is not inserted, continuous lighting of the
2 607 225 7..
battery charge indicator 2 indicates that the mains plug is in-
serted in the socket and that the battery charger is ready for
V 10.8 – 18 operation.
A 1.4
Troubleshooting – Causes and Corrective
Measures
°C 0 – 45
Cause
3 – 10
Continuous lighting of the battery charge indicator 2
No charging procedure possible
kg 0.30
Battery not (properly)
/ II
inserted
10.8 V 14.4 V 18 V
Battery contacts
contaminated
65 65 80
90 90 105
Battery pack defective
– 130 160
Battery charge indicator 2 does not light up
– 180 210
Mains plug of battery charger
not plugged in (properly)
Socket outlet, mains cable or
battery charger defective
Working Advice
With continuous or several repetitive charging cycles without
interruption, the charger can warm up. This is not meaningful
and does not indicate a technical defect of the battery charg-
er.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Maintenance and Service
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
English | 5
Corrective Measure
Properly insert battery into
battery charger
Clean the battery contacts
(e.g. by inserting and remov-
ing the battery several times)
or replace the battery
Replace the battery
Insert mains plug (fully) into
the socket outlet
Check the mains voltage;
have the battery charger
checked by an authorised af-
ter-sales service agent for
Bosch power tools
1 609 92A 40K | (28.11.17)