Publicité
Les langues disponibles
Les langues disponibles
STUDER REVOXx
REVOX
IR REMOTE
CONTROL SYSTEMS
E 5/4*
Hand-held
remote
control
transmitter
All
tape
transport
functions
as well
as
the
monitor
function
of the
cassette
tape
recorder
can
be
initiated
from the remote
controls
B201,
8201CD,
and B205.
The re-
corder
is switched
on when
one
of the
keys
PAUSE,
<<,
>>,
PLAY or STOP
is pressed,
and the corresponding
function
is
executed.
The
POWER
switch
on the unit
itself
can be
in
the
ON or STANDBY
position.
The record
function
is acti-
vated by simultaneously
pressing
REC and PAUSE
or REC
and
PLAY.
For remote
control
of the monitor
function
(change-
over
SOURCE/TAPE),
the MONITOR
switch
on the recorder
must
be in SOURCE
position.
The POWER
OFF key switches
off
all
remote
controlled
units.
With
the * key two
tape
machines
can
be controlled
independently
of each
other
by address~
ing the * function
in one
of the units.
Addressing
the * function
Open
the
jumper
(JS)
on the
IR receiver
PCB of one
of
the tape recorders
(refer
to component
diagram).
AS a con-
sequence
all
commands
of
this
unit
will
be executed
only
when
the * key
is pressed
first
and held,
and
in addition
the corresponding
function
key
is pressed.
5.3.2
REVOX B251,
B252 Tape Remote
PCB
Application:
When
the Tape Remote
PCB 1.725.780
is installed
in
the
B251/B252
amplifier,
an
open
reel
recorder
B77
or
a
cassette
tape
recorder
8710 MKI
can be controlled
via the
IR receiver
of the B251/B252.
Bill
of materials:
1x TAPE
REMOTE
PCB
1.725.780
1x 9-Conductor
cable
1.023.702.00
1x TAPE
REMOTE
cable
harness
1.725.940.00
2x Cable
cleats
35.03.0121
2x Screws
M3 x 8
21.26.0355
2x Nuts
M3 x 0.8
22.01.8030
2x PCB holders
35.03.0130
Warning:
The TAPE
REMOTE
PCB 1.725.780
contains
electrostatically
sensitive
components
(ESE).
The
corresponding
provisions
are absolutely
necessary
for
installation.
Installation:
s Remove
top amplifier
cover
Cunfasten
two
screws).
a Push
out
the blank-off
cover
(rear/connectorpanel,
TAPE
TRANSPORT
B77/B710)
and
instatl
the 10-pin
DIN socket
of
the TAPE
REMOTE
cable
harness
in this position
(A).
Fig.5.10
e Insert
the two PCB
holders
into
the
small
holes
on
the
side
panel
(D)
and snap
the PCB
(cable
harness
facing
the
front
panel)
into
the
holders
(caution:
electrosta-
tically
sensitive
components!).
a Plug the small
cable
harness
into
the
CIS
socket
(E).
= Fix
the two cleats
in position
(B)
and
(C)
(peel off the
plastic
film at the gtueing
position
and press
the cleat
firmly
against
the metal
sheet).
a Draw
the
Large cable
harness
(as
illustrated
in
Fig.
5.15)
into the cable
clip and plug
it into socket
(F) of
the
TAPE
REMOTE
PCB.
a Reinstall
top cover.
a Plug
the
cable
1.023.701.00
into
the
TAPE
REMOTE
B77/B710
socket
of the
amplifier
and
into
the
TAPE
DRIVE
socket
of the open
reel
or cassette
tape
recorder.
Operating
tips:
The
connected
open
reel
or
cassette
tape
recorder
can be
remote
controlled
only via the B251/B252
amplifier.
The
unit
cannot
be switched
on or off
from
the
IR
control,
the power
switch
of the unit
has
to be
actuated
for
this
purpose.
Additional
information
can be found
in
the operation
instructions
(Section
2.1.2).
remote
Publicité
