STUDER REVOX B205 Instructions De Service page 45

STUDER REVOX
REVOX !R REMOTE CONTROL SYSTEMS
E 1/8
Instruction set of B203-IND CEVENT 06 ... 45):
General:
The input format of the switching events 06... 45 dif-
fers from that of the switching events 01 05 prin-
cipatly in that no stop time is entered.
Each switching event can be terminated or stopped by the
succeeding one. Two different input types permit versatile
programming with short string Lengths.
1. IR format
RREKKKKEKKEREK
OEaabcccccc(c) Ideeeefgggghhhhhh<
Layout:
Number of switching event
Type of date :
Date
Identification for IR format
Terminal No. for 1st command
1st IR command
Terminal No. for 2nd command
2nd IR command
Start time
Fao +7OD Gana TH
e_a Number of switching event:
06 EVENT 06
ls evtuT 45
a_b Type of date:
W Weekly on specific days
D Once on a specific date
ac Date:
1000000 Sundays Cif "b" = WwW
0100000 Mondays Cif "b™ = Ww)
0010000 Tuesdays Cif "b" = Ww)
0001000 Wednesdays Cif "b" = WwW)
0000100 Thursdays Cif "b" = W)
0000010 Fridays Cif "b" = W)
0000001 Saturdays (Cif "b" = W)
Several or alt days can be set at the same
time.
ddmmyy Date: Day (dd), Month (mm), Year (yy), Cif "b"
=D).
a_I Identification of IR format:
I Informs the B203 that the subsequent
transmitted in the IR format.
command is
a_d Terminal No. for 1st command:
1 Device on terminal 1
Device on terminal 8
ae First IR command:
eeee 4-digit HEX entry. ALL IR commands Listed in the
"SERIAL LINK" protocol can be used (e.g. O&37 =
PLAY/NEXT) .
e f Terminal No. for 2nd command:
1 Device on terminal 1
Device on terminal 8
a gq Second IR command:
gggg 4-digit HEX entry.
"SERIAL LINK"
PLAY/NEXT).
If the second IR command is not used, the first one
is to be repeated.
ALL IR commands Listed in the
protocol can be used (e.g. O&37 =
ah Start time:
hhmmss Start time (24-hour mode) in hours
Minutes (mm), and seconds (ss).
Chh),
2. Format of direct commands
HRKKKKRKKKKKREKRREREREREREEER
String format:
OEaabcccecc(c)ddef f ff f fSqqggqg<
Layout:
Number of switching event
Type of date
Date
Identification for direct command
Terminal No.
Command Letter
Supplementary parameter (if specified in
the command tables of the equipment).
End identification of the direct command
Start time
AeaaVOTD
moun
m_a Number of switching event:
06 EVENT 06
ie a 45
a_b Type of date:
W Weekly on specific days
10) Once on a specific date
ac Date:
1000000 Sundays Cif "b" = W)
0100000 Mondays Cif "b" = W)
0010000 Tuesdays Cif "b" = WwW)
0001000 Wednesdays (if "b" = W)
0000100 Thursdays (Cif "b" = Ww)
0000010 = Fridays Cif "b" = W)
0000001 Saturdays (if "b" = W)
Several or all days can be set at the same
time.
ddmmyy Date: Day (dd), Month (mm), Year (yy), Cif "b
type of date" = BD).
a D Identification of direct command:
1) Informs the 8203 that the subsequent command is a
direct command.
ed Terminal No.:
1 Device on terminal 1
Device on terminal 8
a_e Command letter:
e Command Letter (e.g. "P" for PLAY).
The valid command for the individual devices can be
found in the following command tables.
a_f Supplementary parameter:
fftfff
Supplementary parameters such as Locator addresses
are specified in the command tables. They contain
up to 6 digits 0 ... 9.
If no supplementary parameters are specified in the
command table, no entry is needed here.
e S End Identification of the direct command:
s The command must always be terminated with
identification.
Example:
..-CCD4A1542Sqg...
(Terminal 4 sets LOC 1 to 15:42 on 8215)
this
® q Start time:
hhmmss Start time (24-hour mode) in hours
minutes (mm), and seconds (ss).
Chh),