Publicité
Les langues disponibles
Les langues disponibles
STUDER REVOXx
REVOX IR REMOTE CONTROL SYSTEMS
E 1/2
1.2.
DISASSEMBLY
INSTRUCTION
Disconnect
your
hi-fi
system
from
the
AC
power
source
and detach
all
connections
to
the B203
- Timer
Controtler
before
you
open
the unit!
1.2.1
Required
tools
1 Phillips
screwdriver
............
ccc e eee e ec eee Size 1
1 Phillips
screwdriver
"Pozidriv"
..............
Size
4
1) SCROWORAVER
ood bic eee ite kie-a: o'sdeele a0 eis tne She ww ores
Size 2
1 Plastic
alignment
screwdriver
..............00.
Size
1
1 Open-end
wrench
.......
cc
ccc
cece
cece eee
Size
5.5
4 "ESE"
workbench
kit
..........ce
cece wees Part
No.
46 200
Recommendation:Line
the
workbench
with
foam
rubber
to
prevent
marring
of the housing
surfaces.
Note:
When
you
remove
or
reinstall
any
electronic
components,
it
is essential
to follow
the MOS
component
handling
re-
commendations
given at the beginning
of this manuat.
1.2.2
Reassembly
Reassemble
the
unit
by following
the
disassembly
in-
structions
analogously
in the reverse
order
and also
fol-
lowing
the
specific
assembly
notes.
1.2.3
Top cover
ttre
SA
se Unfasten
2
screws
[1]
on the rear
while
you press
the
back
of
the cover
Lightly
down.
(The
cover
has
been
pretensioned
by the
factory.)
Assembly
note:
Stide
the
panel,
screws.
cover
then
press
first
into
the groove
on
the
front
it down
on the back
and
tighten
the
1.2.4
Side panels
a Unfasten
2 screws
each
[2].
1.2.5
Front
trim strip
m Remove
top cover
(Section
1.2.3).
a From
the top of the unit:
Unfasten
2 screws
[3] with
their
serrated
lock
washers
(remove
ground
contact
springs).
= On the bottom
of the housing:
Unfasten
2 screws
[41].
m= Remove
front
trim strip.
Assembly
note:
The
ground
contact
springs
are to be installed
between
the
housing
and the
front
trim
strip.
1.2.6
LC display
Remove
top cover
(Section
1.2.3).
Remove
front
trim
strip
(Section
1.2.5).
Detach
connector
to distributor
board.
Unfasten
4 screws
[5] with
their
spacer
sleeves.
1.2.7
IR receiver
rR
TERENAS
@ Remove
top cover
(Section
17.2.3).
a Remove
front
trim
strip
(Section
1.2.5)
ea Unfasten
3 screws
[6]
1.2.8
Distributor
board
er
tn
Remove
top cover
(Section
1.2.3).
Remove
front
trim
strip
(Section
1.2.5).
Unfasten
B77/B8710
socket
(2 screws
with
nuts).
Detach
connector
to LC display.
Remove
IR receiver
(Section
1.2.7).
Unfasten
5 screws
[7].
Skide
the distributor
board.
to
the
right by approx.
3 cm so that
the connecting
cable
is
freed.
Set
the
circuit
board
upright
and
carefully
Ccable)
remove
it.
(535)
(51053 £61£616]
Publicité
