Télécharger Imprimer la page

Electrolux IK 225 10 RE Mode D'emploi page 21

Masquer les pouces Voir aussi pour IK 225 10 RE:

Publicité

Les langues disponibles

Les langues disponibles

Setting up
• Standard EN 378 specifies that the room in which you install
your appliance must have a volume of 1 m
refrigerant used in the appliance, so as to avoid the formation of
inflammable gas/air mixtures in the room where the appliance
is located in the event of a leak in the refrigerant circuit. The
quantity of refrigerant used in your appliance is indicated on the
type plate on the inside of the appliance.
Connecting to the mains
Power supply (AC) and voltage at the operating point must comply
with the details on the type plate, which is located inside the appli-
ance on the left-hand side. The socket must be fused with a 10 A
fuse or higher, it must be away from the rear of the appliance and
must be easily accessible.
Connect the appliance with a properly earthed fused plug
and socket only.
Saving energy
- Always ensure good ventilation. Do not cover ventilation open-
ings or grille.
- Do not place appliance in areas of direct sunlight or next to a
stove, heater or similar object.
- The energy consumption depends on the installation conditions,
e.g. the ambient temperature.
- Keep the time the appliance is open to a minimum.
- Store food logically.
- Ensure that all food is well packed and covered for storage. This
will prevent frost from forming.
- First cool warm food to room temperature before storing it.
- Defrost frozen food in the refrigerator.
- If there is a thick layer of frost in the appliance: defrost the appli-
ance.
Operating and control elements
Temperature display
1
Temperature buttons
2
On/Off button
3
button
4
Child lock
5
Switching the appliance on and off
You are recommended to clean the appliance before switching it
on for the first time (see „Cleaning").
Switching on: Press the On / Off button
display lights up/flashes.
Switching off: Press the On / Off button for approx. two seconds
so that the temperature display goes out.
per 8 g of R 600a
3
3
so that the temperature
3
Setting the temperature
The appliance is pre-set for normal operation. We recommend
temperatures of +5°C in the refrigerator.
• To reduce the temperature:
Press the DOWN button.
• To increase the temperature/warmer:
Press the UP button.
- While you are entering the temperature, the set tempera ture will
flash on the display.
- When you press the temperature setting buttons for the first time,
the most recent setting is displayed.
- You can change the settings in increments of 1°C by briefly
pressing the buttons again. If the buttons are held down the
temperature setting will change faster.
- The system switches over automatically about 5 seconds after
the button was last pressed and displays the average cooling
temperature.
- You can change the temperatures in the refrigerator between
9°C and 4°C.
• The temperature in the NaturaFresh compartment is control-
led automatically, between 0 and 3°C. If you want to increase or
decrease the temperature, e.g. for storing fish, you can change
the NaturaFresh temperature yourself. See "Additional func-
tions" for more information.
Temperature display
The average temperature in the refrigerator compartment is displayed
in normal mode. If
to
F 0
F 5
has a fault. Consult the customer service department.
Button
4
The
button switches the refrigerator compartment to maximum
cooling. This is recommended particulary if you wish to cool large
quantities of fresh food as fast as possible. The refrigeration tem-
perature drops to the level of the coldest temperature control setting.
Switching on: Press the
button briefly so that the LED comes on.
2
1
appears in the display, the appliance
GB
21

Publicité

loading

Ce manuel est également adapté pour:

Ik 225 10 li