Publicité
Les langues disponibles
Les langues disponibles
CONNECT TO A PROPERLY GROUNDED OUTLET
ONLY
Grounded outlet
1
Grounded outlet box
2
Grounding pole
3
OPERATING SAFETY RULES AND
PRACTICES
Owner/User Responsibility
The owner and/or user must have an understanding of the
manufacturer's operating instructions and warnings before
using this device.
Warning information should be emphasized and under-
stood.
If the operator is not fluent in English, the manufacturer's
instructions and warnings shall be read to and discussed
with the operator in the operator's native language by the
purchaser/ owner, making sure that the operator compre-
hends its contents.
Owner and/or user must study and maintain for future ref-
erence the manufacturers' instructions.
Before starting operation, the device must be in the oper-
ating position.
Do not start or operate the device, any of its functions or
attachments, from any place other than from the designat-
ed operator's position.
Before leaving the operator's position:
1 bring the device to a complete stop;
2 if the device must be on an incline, block the wheels.
Maintain a safe distance from the edge of ramps, plat-
forms, and other similar working surfaces.
Do not add to, or modify the device.
Do not block access to fire aisles, stairways or fire equip-
ment.
Traveling
Yield the right of way to pedestrians and emergency vehi-
cles such as ambulances and fire trucks.
Cross railroad tracks at an angle wherever possible. Do
not park closer than 6 ft (1800 mm) to the nearest rail of a
railroad track.
Keep a clear view of the path of travel and observe for oth-
er traffic, personnel, and safe clearances.
Under all travel conditions, operate the device at a speed
that will permit it to be brought to a stop in a safe manner.
Do not indulge in stunt driving or horseplay.
Slow down for wet and slippery floors. Before driving over
a dockboard or bridge plate, be sure that it is properly se-
General
cured. Drive carefully and slowly across the dockboard or
bridge plate, and never exceed its rated capacity.
When negotiating turns, reduce speed to a safe level con-
sistent with the operating environment. Make the turns
smoothly.
Operator care of the device
If the device is found to be in need of repair or in any way
unsafe, or contributes to an unsafe condition, the matter
shall be reported immediately to the user's designated au-
thority, and the device shall not be operated until it has
been restored to safe operating condition.
If during operation the device becomes unsafe in any way,
the matter shall be reported immediately to the user's des-
ignated authority, and the device shall not be operated until
it has been restored to safe operating condition.
Do not make repairs or adjustments unless specifically au-
thorized to do so.
MAINTENANCE AND REBUILD PRACTICES
Operation of the device may be hazardous if maintenance
is neglected or repairs, rebuilds, or adjustments are not
performed in accordance with the manufacturer's design
criteria. Therefore, maintenance facilities (on or off premis-
es), trained personnel, and detailed procedures shall be
provided.
Maintenance and inspection of the device shall be per-
formed in conformance with the following practices:
1 a scheduled planned maintenance, lubrication, and in-
spection system shall be followed; consult the manufac-
turer's recommendations.
2 Only trained and authorized persons shall be permitted
to operate a powered floor scrubber. Operators of pow-
ered floor scrubbers shall be qualified as to visual, audi-
tory, physical, and mental ability to operate the
equipment safely.
Avoid fire hazards and have fire protection equipment
present in the work area. Do not use open pans of fuel or
flammable cleaning fluids for cleaning parts.
FIRE SAFETY STANDARD
Any device not in safe operating condition shall be re-
moved from service.
Repairs shall not be made in Class I, Class II, and Class III
locations.
Fire Prevention.The device shall be kept in a clean condi-
tion and reasonably free of lint, excess oil, and grease.
Noncombustible agents are preferred for cleaning the de-
vice. Flammable liquids [those having flash points at or
above 100°F (37,8°C)] are not allowed. Precautions re-
garding toxicity, ventilation, and fire hazard shall be appro-
priate for the agent or solvent used.
Nameplate Visibility. The device type designations as
shown on the nameplate and the type markers shall not be
covered over with paint so that their identification informa-
tion is obscured.
English
5
Publicité
