Télécharger Imprimer la page

EGO PRO X STX3800 Mode D'emploi page 9

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 22
You may use this product for the purposes listed below:
Trimming: used for removing grass and weeds up against
walls, fences, trees and borders.
Cutting: used for cutting the grass that is difficult to
reach using a normal mower.
NOTICE: The tool is to be used only for its prescribed
purpose. Any other use, for example hedge trimming,
is deemed to be a case of misuse.
ATTACHING/DETACHING THE BATTERY CABLE
Use only with EGO's battery packs and chargers
listed in Fig.A2
Fully charge before first use.
To Install Battery cable (Fig.M)
Align
of plug with
of line trimmer. Insert the plug into
the machine until the green seal completely disappeared
into the socket.
To Remove
Release the battery cord from the mounting groove and pull
out the plug from the line trimmer.
HOLDING THE LINE TRIMMER
WARNING: Dress properly to reduce the risk
of injury when operating this tool. Do not wear
loose clothing or jewelry. Wear eye and ear/hearing
protection. Wear heavy duty, long trousers, boots
and gloves. Do not wear short trousers, sandals or go
barefoot.
Before operating, hold the trimmer with both hands, one
hand on the rear handle and the other on the front-assist
handle which shall be straight. Then check for balanced
footing and a proper cutting distance.
NOTICE: The trimmer head is parallel to the ground at
a proper cutting distance without the operator bending
over.
STARTING/STOPPING THE LINE TRIMMER (Fig. N)
To Start
Push the lock-off Lever to position "ON", push the locking
tongue forward then depress the switch trigger. The trigger
is stepless speed adjusting. The more you pull up the
trigger, the higher speed it is.
N-1 Lock-off Lever
N-2 Locking tongue
N-3 Switch Trigger
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — STX3800
To Stop
Release the switch trigger and push the lock-off button
back to position "OFF".
WARNING: Always unplug the battery connector
from the socket during work breaks and after finishing
work.
USING THE LINE TRIMMER
WARNING: To avoid serious personal injury, wear
goggles or safety glasses at all times when operating
this unit. Wear a face mask or dust mask in dusty
locations.
Clear the area to be cut before each use. Remove all
objects, such as rocks, broken glass, nails, wire, or line,
that can be thrown or become entangled in the cutting
attachment. Clear the area of children, bystanders,
and pets. At a minimum, keep all children, bystanders
and pets at least 15m away; there still may be risk to
bystanders from thrown objects. Bystanders should be
encouraged to wear eye protection. If you are approached,
stop the motor and cutting attachment immediately.
Before each use, check for damage/worn parts
Check the bump head, guard and loop handle and replace
the parts that are cracked, warped, bent, or damaged in
any away.
The line-cutting blade on the edge of the guard can
dull over time. It is recommended that you periodically
sharpen it with a file or replace it with a new blade.
WARNING: Always wear gloves when mounting
or replacing the guard or when sharpening or replacing
the line-cutting blade. Note the location of the blade on
the guard and protect your hands from injury.
Check for blockage of the trimmer head
To prevent blockage, keep the trimmer head clean.
Remove grass clippings, leaves, dirt and any other
accumulated debris before and after each use.
When blockage happens, stop the line trimmer and
remove the battery, then remove any grass that may
have wrapped itself around the motor shaft or trimmer
head.
After each use, clean the trimmer.
CAUTION:
Obstructions in the vents will prevent
the air from flowing into the motor housing and result in
overheating or damaged of the motor.
Use only mild soap and a damp cloth to clean the tool.
Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
EN
9

Publicité

loading