Bosch GDR 18V-220 C Professional Notice Originale page 18

18 | English
Changing the Tool
Inserting the application tool (see figure A)
Insert the application tool all the way into the tool holder (1).
Screwdriver bits (13) can be inserted using a universal bit
holder with ball catch (14).
NOTE: If the application tool does not go in easily, pull the
locking sleeve forward and then push the application tool
into the tool holder as far as it will go.
NOTE: Make sure that the application tool clicks into place
and is secure.
Removing
Pull the locking sleeve (2) forward and remove the applica-
tion tool.
Inserting the Bluetooth® Low Energy Module
GCY 42 (Accessory)
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
Operation
Method of Operation
The tool holder (1) (with the application tool) is driven by an
electric motor via a gear and impact mechanism.
The working procedure is divided into two phases:
Screwing in and tightening (impact mechanism in action).
The impact mechanism is activated as soon as the screwed
connection runs tight and load is therefore put on the motor.
The impact mechanism then converts the power of the mo-
Status indications
Status indicator for power Meaning/cause
tool (15)
Green Status OK
Yellow Critical temperature has been reached or re-
chargeable battery is almost empty
Illuminated red Power tool has overheated or rechargeable
battery is empty
Flashing blue Power tool is connected to a mobile device or
settings are being transferred
Speed preselection
With the speed preselection button (19), you can preselect
the required speed in three stages. Press button (19) as of-
ten as needed until the required setting is indicated in the
speed indicator (20). The selected setting will be saved.
You can also preselect the speed using the Bosch Toolbox
app.
The required speed depends on the material and the work-
ing conditions; it can be ascertained through practical tests.
1 609 92A 8HZ | (14.12.2023)
tor to steady rotary impacts. When loosening screws or nuts,
the process is reversed.
Starting Operation
Set the rotational direction (see figure B)
The rotational direction switch (3) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (9) is being pressed.
Right rotation: To drive in screws and tighten nuts, press
the rotational direction switch (3) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (3) through to the right
stop.
Adjusting the Speed/Impact Rate
You can adjust the speed/impact rate of the power tool when
it is on by pressing in the on/off switch (9) to varying ex-
tents.
Applying light pressure to the on/off switch (9) results in a
low rotational speed/impact rate. Applying increasing pres-
sure to the switch increases the speed/impact rate.
Switching on/off
To start the power tool, press and hold the on/off switch
(9).
Worklights (10) and (18) light up when the on/off switch (9)
is lightly or fully pressed, meaning that the work area is illu-
minated in poor lighting conditions.
To switch off the power tool, release the on/off switch (9).
User interface (see figure C)
The user interface is used to preselect the speed and work-
ing mode and to indicate the status of the power tool.
Solution
–
Run the power tool at no load and allow it to
cool down, or replace or charge the battery
soon
Allow the power tool to cool down, or replace
or charge the battery
–
Basic speed setting at level
1
[min
Number of speed settings
3
You can use the button for speed preselection (19) to
preselect the required speed, even during operation.
2 3
–1 –1 –1
] [min ] [min ]
0–800 0–2300 0–3400
Bosch Power Tools