Elica PRF0180599 Prescriptions De Montage Et Mode D'emploi page 6

GENERAL SAFETY
•Do not make electrical or mechanical changes on the product or on the exhaust pipes. •Before doing any cleaning or
maintenance work, disconnect the product from the mains power supply by removing the plug or turning off the mains switch.
•For all installation and maintenance operations, always wear work gloves. •The product can be used by children over the age
of 8 and by people with reduced physical, sensory or mental capabilities or without experience or the necessary knowledge, as
long as they are properly supervised or have been instructed on how to safely use the device and understand the inherent
dangers. •Children must be supervised to make sure that they do not play with the product. •Cleaning and maintenance must
never be performed by children unless they are properly supervised. •The room must have sufficient ventilation when the
product is used at the same time as other appliances burning gas or other fuels. •The product must be cleaned frequently both
inside and out (AT LEAST ONCE A MONTH); always follow the instructions given in the maintenance manual. •Failure to
comply with the rules indicated for cleaning the product and replacing/cleaning the filters may result in the risk of fire. •It is
strictly forbidden to cook food on the flame under the product.• WARNING: •When the hob is on, the accessible parts of the
product may become hot. •Do not connect the product to the electrical power supply until the installation is complete. •The
regulations laid down by local authorities must be strictly followed with regard to the technical and safety measures to adopt
for fume extraction. •The extracted air must not be conveyed through the same ducts used to extract the fumes generated by
gas combustion or other types of combustion products. •Do not use or leave the product without appropriately installed lamps,
as this may result in the risk of electric shock. •The product must NEVER be used without the grille correctly fitted. •The
product must NEVER be used as a support surface unless expressly indicated.
● Range hoods and other cooking fume extractors may adversely affect the safe operation of appliances burning gas or other
fuels (including those in other rooms) due to back flow of combustion gases. These gases can potentially result in carbon
monoxide poisoning. After installation of a range hood or other cooking fume extractor, the operation of flued gas appliances
should be tested by a competent person to ensure that back flow of combustion gases does not occur.
INSTALLATION SAFETY
•Use the fixing screws supplied with the product only if suitable for the surface; otherwise purchase the correct type of screws.
•Check for accessories (e.g. bags containing screws, warranty certificates, etc.) inside the product (placed there for transport
reasons). If there are any, remove them and keep them safe. • WARNING: Failure to install screws and fasteners in
accordance with these instructions may result in electrical hazards. •The exhaust pipe is not supplied and must be purchased.
•The diameter of the exhaust pipe must be equivalent to the diameter of the connecting ring. •For installation of the product on
the hob, respect the height indicated in the drawings •The minimum distance between the surface of the container supports on
the cooker and the lowest part of the range hood must not be less than 50 cm (not less than 57 cm only for Australia and New
Zealand) for electric cookers and 57 cm for gas or mixed cookers. •If the installation instructions of the gas cooker specify a
greater distance, take it into account.
ELECTRICAL CONNECTION SAFETY
•The mains voltage must correspond to the voltage indicated on the label found inside the product. •If it features a plug,
connect the product to a socket that complies with current standards, located in an area accessible even after installation. •If it
does not feature a plug (direct connection to the mains) or the plug is not located in an accessible area, even after installation,
apply a standard double pole switch that ensures complete disconnection from the mains in category III overvoltage
conditions, in accordance with the installation rules. • Warning! The power cable must be replaced by the authorised technical
support service or by a person with similar qualifications.
LED temperature adjustment
Once the product has been installed, before refitting the grease filter and the perimeter suction panel, it is possible to adjust
the temperature of the LED, from warm light to cool light, in order to match it with the light in your room.
The available temperatures are:
W = 3000K warm
N = 3500K medium warm
C = 4000K cool.
OPERATION
Please note! This hood features an automatic operation system (see the paragraph "VOC sensor calibration").
Calibration occurs automatically each time the hood is reconnected to the electrical network (e.g.: the first time it is
installed after a blackout). It can also be performed manually (see the paragraph "VOC sensor calibration - manual").
During calibration, which lasts 5 minutes, the controls will flash and only the light button can be used.
6