EINHELL 4350413 Mode D'emploi page 13

or Rechargeable (Nickel Cadmium, Nickel
Metal Hydride, or Lithium-Ion) batteries.
6. Do not dispose of batteries in fi re.
7. Batteries should be recycled or disposed of
as per state, provincial and local guidelines.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
Special safety instructions
•
Hold the power tool by insulated gripping
surfaces only, because the router bit may
contact its own cord. Cutting a "live" wire
may make exposed metal parts of the power
tool "live" and could give the operator an
electric shock.
•
Use clamps or another practical way to
secure and support the workpiece to
a stable platform. Holding the workpiece
by your hand or against the body leaves it
unstable and may lead to loss of control.
•
Before you put the electric router into
operation, check to ensure that the router bit
is firmly seated and runs smoothly!
•
Never use a low quality or damaged router bit.
•
Only use router bits whose shaft diameter
complies with the specifications in the instruc-
tions.
•
The maximum speed specified for the router
bits can't be exceeded.
•
Never cut over metal parts, screws, nails, etc.
•
To avoid damage to the router, make sure
there are no foreign objects stuck to the work-
piece.
•
Always guide the router with both hands.
•
Let the router reach full speed before
plunging the router bit into the workpiece.
•
If the router becomes clogged with work
debris, switch it off. Let the router come to a
complete stop. Remove the debris with a long
stick and not with your fingers.
•
Let the router run to a complete stop before
removing the workpiece or setting down the
tool.
•
Always cut on a counter-rotating basis.
•
Watch out for the reaction torque of the tool,
especially if the router becomes jammed.
•
When you have finished your work, slide the
tool back to starting position.
•
Use only properly sharpened router bits.
•
Clamp the router bit by friction-locking.
•
For deep cuts, carry out the work in several
steps according to the material in question.
Anl_TP_RO_18_Set_Li_BL_SPK7_USA.indb 13 Anl_TP_RO_18_Set_Li_BL_SPK7_USA.indb 13
EN
•
Use only router bits with a shaft diameter
which matches the integrated collet.
•
Use only router bits which are suitable for the
speed of the electric tool.
SAVE THESE INSTRUCTIONS
2. Layout and items supplied
2.1 Layout
1. Cordless routing unit
2. Unlock/lock button
3. On/Off switch
4. Speed adjusting dial
5. Spindle lock
6. Collet nut
7. Handles
8. Depth stop adjustment screw
9. Scale
10. Depth pointer
11. Lock nut
12. Quick adjust button
13. Turret stop
14. Depth stop
15. Safety guard
16. Edge guide holder
17. Edge guide holder lock knobs
18. Edge guide lock knob
19. Plunge base lock lever
20. Plunge base dust chute
21. Dust chute lock knob
22. Routing unit lock knob
23. Height adjuster lock knob
24. Height adjuster knob
25. Edge guide lock knob (fi xed base)
26. Fixed base dust chute
27. Countersunk head screw for fi xed base dust
chute
28. Open-ended wrenches
29. Template guide
30. ⁄ " Collet
1
4
31. Plunge base routing shoe
32. Trimmer roller guide
32.1. Guide roller
32.2. Retaining knob
32.3. Adjustment knob
33. Compass point
34. Edge guide
34.1. Wing nut
35. Plunge base
36. Fixed base
37. LED lamp
- 13 -
24.05.2023 09:44:14 24.05.2023 09:44:14