HIKOKI NT 1865DA Mode D'emploi page 20

English
○ Use nail strip of more than 10 nails.
○ Use an unbroken nail strip with nails of all the same
length.
The Nailer is now ready to operate.
Removing the nails:
Pull the nail feeder (B) backward. (See Fig. 12)
Return the nail feeder (B) forward quietly while pushing
the nail feeder (A).
Pull out nails from the back of the magazine. (See
Fig. 13)
<NT1850DBSL>
(1) Lightly press the stop lever and gently pull out the
magazine cover. (See Fig. 14)
(2) Set nail strip into the magazine and keep the points of
nails in contact with Groove. (See Fig. 15)
NOTE
The nails shown in page 16 can be loaded onto the side
guide groove of the magazine without any adjustment.
Always keep the points of nails in contact with Groove.
Magazine
Side guide
groove
Nail
Groove
(3) Slide the nail strip into the blade guide. (See Fig. 16)
(4) Confi rm that nail strip is placed with side guide grooves
and Groove properly, then push the magazine cover
forward to be latched.
HOW TO USE THE NAILER
WARNING
○ NEVER point tool at yourself or others in work area.
○ Keep fi ngers AWAY from trigger when not driving nails to
avoid accidental fi ring.
○ Do not use the electrical cord if damaged. Have it
repaired immediately.
○ Choice of triggering method is important.
Please read and understand "1. Nailing procedures"
found below.
○ Before starting work, check the nailing operation
switching device.
This HiKOKI nailer includes a nailing operation switching
device.
Before starting work, make sure that the switching
device is properly set.
If the switching device is not set properly, the nailer will
not operate correctly.
○ Never place your face, hands or feet near fi ring head
when using.
○ Do not drive nails on top of other nails or with Nailer at too
steep of an angle; nails can ricochet and hurt someone.
○ Do not drive nails into thin boards or near corners and
edges of workpiece. Nails can be driven through or away
from workpiece and hit someone.
○ Never drive nails from both sides of a wall at the same
time. Nails can be driven into and through the wall and
hit a person on the opposite side.
○ Never use Nailer which is defective or operating
○ Do not use Nailer as hammer.
○ Remove all remaining fasteners and battery from nailer
○ Remove battery from Nailer when:
This HiKOKI nailer is equipped with a nailer operation
switching device.
Use FULL SEQUENTIAL ACTUATION MECHANISM or
CONTACT ACTUATION MECHANISM in accordance with
the work to be performed.
Explanation of the various nailing operations
○ FULL SEQUENTIAL ACTUATION MECHANISM:
○ CONTACT ACTUATION MECHANISM:
Gap
[Dry-fi re lockout mechanism]
CAUTION
1. Nailing procedures
(1) Intermittent operation (Trigger fi re)
WARNING
○ For intermittent operation, Set the nailing operation switch
20
abnormally.
when:
1) doing maintenance and inspection;
2) checking proper operation of push lever and trigger;
3) attaching or removing the nose cap;
4) cleaning a jam;
5) it is not in use;
6) leaving work area;
7) moving it to another location; and
8) handing it to another person.
1) loading nails;
2) turning the adjuster.
First, press the push lever against the wood; next, pull
the trigger to drive the nail.
Follow the same sequence to continue driving nails.
After nailing once, nailing will not be possible again until
remove fi nger from the trigger and lift the tool off the
wood surface completely.
CONTACT ACTUATION can follow two diff erent
sequences, depending on your use.
To drive several nails:
1. Pull the trigger.
2. Press the push lever against the wood to drive the
nail.
3. If the trigger is held back, a nail will be driven each
time the push lever is pressed against the wood.
To drive a single nail:
1. Press the push lever against the wood.
2. Pull the trigger to drive the nail.
3. Remove your fi nger from the trigger and remove the
nailer from the wood.
The NT1865DBAL, NT1865DBSL and NT1865DA
employ a preventive mechanism for unloaded operation.
The NT1865DBAL, NT1865DBSL and NT1865DA enter
a state where the push lever cannot be pushed up. This
takes place when the magazine is not loaded with nails
or when the remaining number of nails becomes less
than 6 or 9.
Use caution not to throw the push lever tip onto wood
when the push lever cannot be pushed up.
This Nailer is equipped with the push lever and does not
operate unless the push lever is depressed.
There are two methods of operation to drive nails with
this Nailer.
They are:
1. Intermittent operation (Trigger fi re):
2. Continuous operation (Push lever fi re):
Use the FULL SEQUENTIAL ACTUATION MECHANISM
setting. (See Fig. 17)
to FULL SEQUENTIAL ACTUATION MECHANISM
(Nailing operation indicator is light in blue.) (i.e. Set to
SINGLE ACTUATION MECHANISM.)