Publicité
Les langues disponibles
Les langues disponibles
English
1. To move the hang hook
hold the hang hook
7
and securely tighten the screws
2. Remove the screws
11
and reassemble the hang hook
tighten the screws.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: Proper material preparation
and installation is the responsibility of the
installing contractor.
WARNING: The tubing and hardware must be
used in compliance with applicable building
codes and as approved by the authorities having
jurisdiction. For proper installation procedures
and to reduce the risk of failure resulting in injury or
property damage, follow all published safety and
installation instructions.
CAUTION: Pinch hazard. Keep fingers away from
expander head while in use.
Installing and Removing the Battery Pack
(Fig. G)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
pack out of the tool handle. Insert it into the charger as
described in the charger section of this manual.
Proper Hand Position (Fig. A, H)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the
main handle
.
3
Lock Off (Fig. A)
Your PEX expander is equipped with a trigger lock
1. To lock the trigger switch
the trigger lock
from the left side of the tool.
5
2. To unlock the trigger switch
from the right side of the tool.
10
7
, remove the screws
11
in place. Install removed screws
11
.
on the desired side of the tool
. Be sure to securely
7
8
into the tool handle, align
and firmly pull the battery
9
5
in the OFF postition, push
4
4
, push the trigger lock
Trigger Switch (Fig. A)
that
CAUTION: To reduce the chance of damage to the tool
ALWAYS lock the tool when not in use.
1. To turn the tool on, squeeze the trigger switch
2. To turn the tool off, release the trigger switch.
nOTE: Depressing the trigger switch
worklight
6
off after twenty seconds. To turn off the LED worklight
immediately, remove and reinstall the battery.
nOTE: The LED worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Creating a PEX Tubing Connection
(Fig. A, I, J)
WARNING: Prior to use inspect all workpieces for
cracks, defects or wear. Defective workpieces may shatter.
CAUTION: Using incorrectly sized expansion heads
may result in a faulty connection, possibly resulting in
damage to property.
To create a proper PEX tubing connection:
1. Select appropriate expander head
and, if needed, remove any dirt and debris.
2. Using a clean, lint-free cloth, apply a thin coat of D
DCE400GR grease
over-lubricate.
3. Make a perpendicular cut to PEX tubing to the needed
length. OnlY use cutters designed for PEX tubing.
4. Slide the PEX ring
until it sits properly against the ring stop. If the PEX ring
does not have a stop, leave an over-hang of no more
than 1/16" (1.6 mm) as shown in Fig. J.
5. Insert the expander head into the PEX tubing as shown
in Fig. I.
6. Squeeze the trigger switch
begin to expand, retract, and rotate slightly.
nOTE: Hold the ring and tubing so they do not rotate with
the head.
PEX spec
3/8"
1/2"
5/8"
3/4"
1"
1"
1-1/4"
1-1/2"
NOTE: DO NOT EXPAND MORE TIMES THAN NECESSARY.
.
nOTE: The number of expansions needed may vary
depending on temperature or user technique. To avoid over-
expanding the PEX tubing, do not keep tool in the expanded
5
position with PEX tubing in place.
7. After achieving the recommended number of expansions,
remove the tubing when the expander cone
. The LED worklight
6
will automatically turn
10
to the expander cone
13
over the end of the PEX tubing
4
. The expander head will
Recommended Number
of Expansions
6-7
8-9
8-9
10
20
7-8
9-10
8-9
.
4
will activate the LED
4
6
to match the tubing
2
WALT
e
. DO nOT
1
12
Recommended
Accessory
DCE40038
DCE40012
DCE40058
DCE40034
DCE4001
DCE410100
DCE410114
DCE410112
1
segments
Publicité
