DeWalt DCE410 Guide D'utilisation page 14

English
Tool Connect™ Chip (Fig. L)
Optional Accessory
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ chip 15 communicates with an optional
application for your smart device (such as a smart phone
or tablet) that connects the device to utilize the mobile
application for inventory management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
installing the Tool Connect™ Chip
1. Insert the Tool Connect™ Chip
empty pocket 14 .
2. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws
tighten the screws.
3. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including
brush inspection and replacement, when applicable)
should be performed by a factory service center or
an authorized service center. Always use identical
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is
a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/account‑login.
12
into the
15
and
16
Three‑Year Limited Warranty
For warranty terms, go to www.dewalt.com/support/
warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D WALT Industrial Tool Co., 701 East
e
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
Troubleshooting Guide
if the fittings will not seal properly:
1. Check to see if the expander head is screwed
on tightly.
‑ Tighten the head.
2. Check to see if the expander head segments are
bent or misaligned.
‑ Replace the expander head.
3. Are the expander head segments not properly
contracting between expansions?
‑ Clean and relubricate the expander head.
Check to see if the expander cone is
‑
properly lubricated.
‑ Clean and relubricate the expander cone.
4. has the fitting been damaged?
‑ Replace the fitting.
5. Was the PEX tubing removed while the expander
cone was in the expanded position?
‑ For PEX tubing 1" (25 mm) and below, cut 2"
(50 mm) off the end of the PEX tubing and restart the
procedure with a new PEX ring.
‑ For PEX tubing larger than 1" (25 mm), cut 2-3/5"
(66 mm) off the end of the PEX tubing and restart the
procedure with a new PEX ring.
6. is the PEX tubing and ring dry?
‑ Wipe dry with a clean, lint-free cloth.
7. is there grease from the expander head inside the
PEX tubing?
‑ Wipe off all grease from inside the PEX tubing and
relubricate the expander head.
The ring slides during the expansion process:
1. is the PEX tubing and ring dry?
‑ Wipe dry with a clean, lint-free cloth
2. Are your hands clean and dry?
‑ Make sure your hands are clean and dry. Oils from
your hands can lubricate the PEX tubing and ring.
3. is the ring being held properly in place?
‑ Use your thumb to hold the ring in place for the first
couple of expansions.
WALT
e
WALT
e