Texas A/S HS619TG Manuel D'utilisation page 14

H. Swing handle
I. Engine (may vary from picture)
J. Belt guard
K. Electric starter - 230V
(HS650TGE / HS700TGE only)
Assembly
The sweeper is almost ready assembled from the
factory. Only a few items remain to be assembled:
Actual model may vary from the illustration shown
Check the tire pressure on both wheels before use.
Correct tire pressure is
24 psi/1.7 bar. Fig 9.
Use of machine with too low tire pressure
can damage the tires!
Right wheel bolt has links thread!
Handy Sweep - all models
1.
Remove the bolts from the base unit then
mount the handle bar and fix the bolts
See figure 3.
2.
Mount the wheels. Pay attention to that right
wheel bolt have links thread and need be
loosen/ tighten opposite direction.
3.
Mount the gear shifter rod to the bracket as
shown in figure 4.
4.
Adjust the bolt (A) in bottom of gear shifter rod
as shown on figure 5. The more the bolt is
tightened, the harder the gear shifter rod
presses against the gear plate. Adjust so that
the gear shifter goes easily into all 4 positions
on the gearplate and stays there.
5.
Pull the cables up to the clutch handles.
Separate the metal parts by turning them
apart. Mount the part with the hook onto the
clutch handle. Assemble the 2 metal parts and
turn it until the cable is tight. See figure 6.
6.
Mount swing handle with enclosed bolts and
nuts. Hold the 2 nuts on the underside while
removing the 2 bolts at the rubber sockets.
The rubber sockets must be mounted under
the handle plate. Attach the swing handle.
Tighten the 2 bolts, while holding the 2 nuts on
the underside. See figure 7.
Only HandySweep 710 models
7.
Mount the brush on each side following the
assembling method 1 or method 2.
See figure 10 (M1 or M2)
Explanation to figure 10, A1:
A. Brush
B. Spacer cup
C. Bracket
D. Bolt
8.
Mount the guard using the enclosed bolt,
washer and nut. Follow the step 1-5 in figure
11. NB: The sideguards have to be mounted
under the main guard.
Operation
Read the instruction manual for the
engine, before use.
Before using the machine, remove bigger objects from
the vicinity. Bigger objects can damage the sweeper.
Also check that all bolts are tightened.
Control oil level before starting the engine.
See included guide.
Start the engine:
1. Open the fuel tap.
2. On a cold engine open the choker.
Note: By a hot engine choke is not required.
3. Turn the throttle cable to "start" position.
4. Pull the recoil starter gently until you feel
resistance in the rope. Then pull quickly and
energetic. Do not at any time let go of the
recoil starter but glide it gently back and pull
again.
5. 230V electric starter (HS650TGE / HS710TGE
only). Plug the cord into electrical outlet and
press the start button. After the engine is
started remove the plug from the socket.
6. Regulate the choker until the engine is running
smoothly.
Stop the engine:
1. Set the throttle to minimum/stop.
2. Turn the fuel tap to the "off" position.
Gear shifter
3 different forward gears and 1 reverse gear can be
selected. See figure 13.
Always release the clutch handle before
changing gear!
Clutch handle A - Forward and Reverse.
To operate the black clutch handle A in figure 12,
activate the handle, so the sweeper will drive forward
or backwards. To change gear, release the clutch
handle and chose the desired gear with the gear
shifter.
Pay attention while reversing. It is important that the
area is cleared, for any obstacle before reversing.
Never reverse the sweeper against a wall, tree or any
other fixed obstacle.
Clutch handle B - Activation of brush.
To operate the black brush handle B in figure 12, push
down the handle and it activates the brush.
The sweeper is equipped with a "dead man's handle",
once released the brush and drive will stop
immediately.
14