Publicité
Les langues disponibles
Les langues disponibles
EnGLIsh
CAUTION: The keyed guard can only be mounted
on grinders where the DWE46229 230 mm shroud
was mounted.
When using the grinder for cutting metal or masonry a Type 1
guard MUST be used. Type 1 guards are available at extra cost
from D
WALT distributors.
e
1. Place the angle grinder on a table, spindle
2. Align the lugs
with the notches
30
3. Press the guard
down and rotate it to the
29
required position.
4. Securely tighten the screw
5. To remove the guard, slacken the screw.
NOTICE: If the guard cannot be tightened by the adjusting
screw, do not use the tool. To reduce the risk of personal
injury, take the tool and guard to a service centre to repair
or replace the guard.
Mounting and Using Diamond Cutting
Wheels (Fig. A, F, G)
WARNING: Only diamond wheels with a negative
rake angle shall be used with cutting shroud. Do not
cut metal. Do not use with bonded abrasive wheels.
1. With the cutting shroud attached to the grinder, press the
front shroud button
7
same time to fully open the cutting shroud.
2. Install the backing flange,
spindle
26
.
IMPORTanT: The DWE46225 comes with two sets of
flanges. Refer to the Flange/Grinder Compatibility Chart at
the end of this section for proper use.
3. Place the wheel
on the locking flange
25
or
17
, and place both on the spindle, against the backing
flange, centreing the wheel on the raised centre of the
backing flange.
4. While depressing the spindle lock button, tighten the
locking flange:
-
Tighten standard locking flange using a wrench.
5. After the diamond cutting wheel is mounted, the cutting
shroud must be closed by pressing the front shroud
button
and the side shroud button
7
6. To remove the wheel, depress the spindle lock button and
loosen the locking flange.
Flange / Grinder compatibility chart
Flange set
Short (silver) flange set:
Locking flange
11
Backing flange
12
22
up.
26
.
22
31
.
and the side shroud button
12
,
14
or spacer
16
, on
,
11
13
at the same time.
8
Grinder
DCG405, DCG406, DCG409
Flange / Grinder compatibility chart
Flange set
Long (black) flange set:
Locking flange
Backing flange
DCG460 flange set:
Spacer
Flange
Depth of Cut Adjustment (Fig. A)
1. Loosen the depth of cut adjustment knob
2. Slide the depth of cut adjustor
note: If the shroud is closed, press the front shroud
at the
8
button
7
move the depth of cut adjustor.
3. Tighten the depth of cut adjustment knob.
Dust Extraction (Fig. A, H)
WARNING: Use only power tools recommended by
D
WALT with this attachment.
e
For more information about D
with this attachment, please contact one of the authorized
services centres listed on the back cover or refer to the full
details of our after-sales service available on the Internet at:
www.2helpU.com.
WARNING: This attachment must be used with a dust
extractor system. ALWAYS wear certified safety face or
dust mask.
nOTE: Ensure hose connection is secure.
nOTE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor vacuum instruction manual for more information.
All D
WALT dust collection shrouds are designed to work with
e
the D
WALT Airlock DWV9000 connector.
e
1. Attach the DWV9000 connector
hose
.
24
2. Unlock the DWV9000 connector
port
1
.
3. Lock the DWV9000 connector
Traditional Dust Extractor Vacuum Hoses
Attach recommended dust extractor vacuum hose to dust
port
1
.
DWE4016, DWE4203, DWE4206,
DWE4207, DWE4216, DWE4217,
13
14
DWE4227, DWE4233, DWE4235,
DWE4237, DWE4238, DWE4246,
DWE4257, DWE4263, DWE4277,
DWE46105, DWE4357, DWE4347,
DWE4369, DWE4377, DCG412,
DCG414, DCG418, D28498,
DWE490, DWE492, DWE494,
DWE496, DWE4001, DWE4056,
DWE4057, DWE4156, DWE4157,
DWE4151, DWE4557, DWE4559,
DWE4579, DWE4597, DWE4599
DCG460
16
17
4
to the desired position.
to open the shroud. This will make it easier to
WALT power tools compatible
e
23
23
23
to secure.
Grinder
5
.
to your dust collector
and slide onto dust
Publicité
