Publicité
Les langues disponibles
Les langues disponibles
DCG460 flange
17
(DWE46229 only)
Intended Use
Your cutting shroud has been designed for professional
masonry cutting applications. It is not intended for use with
metal or wood. It may used only be for dry cutting. Using
the appropriate D
WALT grinder, diamond wheel and dust
e
extractor vacuum can be used to remove the vast majority of
static and airborne dust which without the use of the cutting
shroud could otherwise contaminate the working environment
or pose an increased health risk to the operator and those in
close proximity.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
The cutting shroud is a professional tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Mounting and Removing the Cutting Shroud
Mounting the DWE46225 125 mm Cutting Shroud
(Fig. A, B–D, F)
WARNING: The protective guard for grinding applications
can't be reinstalled, after the shroud is mounted.
Follow the mounting and removing guard instructions in tool
manual to remove the guard from grinder.
1. To the mount DWE46225 cutting shroud on a keyless gear
case, remove the screw
2. Insert the supplied stop screw
Then mount cutting shroud.
3. Press the front shroud button
button
8
at the same time to fully open the cutting shroud
(Fig. F).
4. Loosen the collar screw
the tabs
on the cutting shroud with the slots
21
grinder gear case.
5. Rotate the shroud into the desired working position. The
shroud should be positioned between the spindle and the
operator to provide optimum efficiency.
18
shown in Figure B.
19
as shown in Figure C.
and the side shroud
7
2
on the cutting shroud and align
22
6. Tighten the collar screw
on the gear case. Do not operate the grinder with a loose
cutting shroud.
7. To remove the cutting shroud, loosen the collar screw,
rotate the cutting shroud to align the slots and tabs and pull
up on the cutting shroud.
nOTE: The cutting shroud is pre-adjusted to the
diameter of the gear case hub at the factory. If, after a period
of time, the cutting shroud becomes loose, tighten the collar
screw
2
.
NOTICE: If cutting shroud cannot be secured by
tightening the collar screw, do not use tool. Take the tool
and cutting shroud to a service centre to repair or replace
the cutting shroud.
Mounting the DWE46229 230 mm Cutting Shroud
(Fig. A, D, F)
Follow the mounting and removing guard instructions in tool
manual to remove the guard from grinder.
1. Press the front shroud button
button
at the same time to fully open the cutting shroud
8
(Fig. F).
2. Loosen the collar screw
the tabs
21
grinder gear case.
3. Rotate the shroud into the desired working position. The
shroud should be positioned between the spindle and the
operator to provide optimum efficiency.
4. Tighten the collar screw
on the gear case. Do not operate the grinder with a loose
cutting shroud.
5. To remove the cutting shroud, loosen the collar screw,
rotate the cutting shroud to align the slots and tabs and pull
up on the cutting shroud.
nOTE: The cutting shroud is pre-adjusted to the
diameter of the gear case hub at the factory. If, after a period
of time, the cutting shroud becomes loose, tighten the collar
screw
2
.
NOTICE: If cutting shroud cannot be secured by
tightening the collar screw, do not use tool. Take the tool
and cutting shroud to a service center to repair or replace
the cutting shroud.
Mounting and Removing a Keyed Guard
(Fig. E)
For 230 mm grinders only
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Before
reconnecting the tool, depress and release the
on the
trigger switch to ensure that the tool is off.
CAUTION: Guards must be used with this grinder.
2
to secure the cutting shroud
7
and the side shroud
2
on the cutting shroud and align
on the cutting shroud with the slots
to secure the cutting shroud
2
EnGLIsh
22
on the
21
Publicité
