VONROC TL505XX Traduction De La Notice Originale page 9

• Place the Telescopic Ladder on a firm, level
surface. Ensure the ladder is in closed position
as shown on figure D1.
• Unlock the Storage strap (4).
• Place one foot on the Bottom Rung (5) to stabi-
lise the ladder. Ensure that the front side of the
ladder is facing you.
• Starting with the second rung from the bottom
(as shown in figure D2), use both hands to
grasp the Hand Grips (7) on either side of the
rung and pull upwards to extend the step.
• When each step is fully extended, you should
hear a "click", confirming that the Locking
Mechanisms (6) are engaged for that level.
• Check that all opened rung sections are locked,
the red Locking Mechanisms (6) should be
clearly visible, as shown on figure C2. Meanwhi-
le, the red parts of the Retract Levers (8) should
not be visible. Also ensure that all the distances
between opened rungs are of equal height.
• When all sections are locked, you can use
the ladder. Position the ladder with a correct
angle for a leaning ladder (angle of inclination
approximately 1:4) with the rungs or treads
level (e.g. 1m away from the base of a wall if
extending to climb 4m up).
Opening the ladder to full length (Fig. A, C, D)
If you are opening the Ladder to its full
length, you should always extend from top
to bottom.
• Place the Telescopic Ladder on a firm, level
surface. Ensure the ladder is in closed position
as shown on figure D1.
• Unlock the Storage strap (4).
• Place one foot on the Bottom Rung (5) to stabi-
lise the ladder. Ensure that the front side of the
ladder is facing you.
• Starting with the Top Bar ((1) as shown in figure
D3), use both hands to grasp the Hand Grips (7)
on either side of the rung and pull upwards to
extend the step.
• When each step is fully extended, you should
hear a "click", confirming that the Locking
Mechanisms (6) are engaged for that level.
• Check that all opened rung sections are locked,
the red Locking Mechanisms (6) should be
clearly visible, as shown on figure C2. Meanwhi-
le, the red parts of the Retract Levers (8) should
not be visible. Also ensure that all the distances
WWW.VONROC.COM
between opened rungs are of equal height.
• When all sections are locked, you can use
the ladder. Position the ladder with a correct
angle for a leaning ladder (angle of inclination
approximately 1:4) with the rungs or treads
level (e.g. 1m away from the base of a wall if
extending to climb 4m up).
Closing the ladder (Fig. A, E)
The entire ladder is closed by using the
Retract Levers (8). For safety reasons, the
treads may not be closed separately.
Do not engage the locking mechanisms (6)
manually. Only use the Retract levers (8) to
close the ladder.
• Hold the Telescopic Ladder in an upright position.
• Place one foot on the Bottom Rung (5) to stabi-
lise the Ladder.
• Starting at the rung where the Retract Levers
(8) are placed, use both hands to grasp the
Hand Grips (7) on either side of the rung. Ensu-
re your hands are placed in such way as shown
on figure E, securing you do not catch your
fingers when closing the ladder.
• Then disengage the Retract Levers (8) with your
thumbs by pushing them towards the centre, so
the red parts become visible.
• The ladder will now start closing. For safety
reasons, the ladder has been fitted with a
soft-closing system, preventing the ladder from
closing rapidly.
Transporting the ladder (Fig. A)
Only transport the ladder when the Storage
Strap is locked.
When carrying the ladder, completely close the lad-
der to its most compact form. Ensure the Storage
Strap (4) is locked, securing the ladder.
5. MAINTENANCE
The ladder is designed to function
faultlessly for a long period and with
a minimum of maintenance. Extend its
lifespan by regularly cleaning the machine
and treating it correctly.
EN
9