Publicité
Les langues disponibles
Les langues disponibles
• The top of the bowl is open when the bowl is removed so
that dust can be easily emptied without touching the filter.
• Figure i - Empty the dust from the bowl
• To replace the dust bowl, place it back onto the handle
until it "clicks" firmly into position.
For a more thorough cleaning, remove bowl as
described below.
For a More Thorough Cleaning (Fig. H, J)
nOTE: Either a bag filter
with these vacuums.
• Figure h - Press the dust bowl release button
handle and remove the dust bowl.
• Remove filter from within the bowl.
• Shake or lightly brush any loose dust off filter.
nOTE: The brush on the nozzle can be used to remove dirt
on the filter.
Bag Filter and Pre-Filter (Fig. K1, K2)
The bag filter and pre-filter can be separated to allow for
better cleaning.
Twist the bag filter to separate it from the pre-filter.
• The dust bowl
4
and filters can be washed in warm soapy
water. Allow to dry before placing back into the vac.
• If using a bag filter, twist the two pieces back together
after they have fully dried.
• Place filter back into the bowl pressing firmly to ensure a
secure fit.
• To replace dust bowl, place it back onto the handle until it
"clicks" firmly into position.
iMPORTAnT: Maximum dust collection will only be
obtained with a clean filter and an empty dust bowl. If dust
begins to fall back out of the product after it is switched off,
this indicates that the bowl is full and requires emptying.
• Wash the filters regularly using warm, soapy water and
ensure that it is completely dry before using again. The
cleaner the filter is, the better the product will perform.
• It is very important that the filter is correctly in position
before use.
Nozzle/Accessories (Fig. L, M)
• Figure l - A crevice tool
be extended as shown in Figure l by pulling the extension
piece until it locks into position.
• To store the crevice tool
stopping rib
12
and then push the crevice tool
nozzle until it locks into position.
• Figure M - A brush accessory
and can be flipped upwards for use.
Scented Filter*
BEFORE FIRST USE - Remove bag from the scented pre-filter.
Reassemble per instructions above.
When the vacuum is turned on, the plastic scented filter will
emit an aroma to freshen the air.
WARNING:
- Causes mild skin irritation.
- Toxic to aquatic life.
- Harmful to aquatic life with long lasting effects.
- Dispose of contents/containers to an approved waste
disposal plant.
4
.
7
or a pleated filter
8
will work
2
is built into the nozzle and can
6
into the nozzle press the
6
6
5
is built into the nozzle
nOTE: When the plastic scented filter no longer lets off the
aroma, it can be an indication that the filter needs to be
replaced. See below for information on replacement filters.
*HLVA320JS vacuums are supplied with a scented filter,
though any vacuum covered in this manual can accept a
scented filter.
Replacing the Filters
The filters should be replaced every 6 to 9 months and
whenever worn or damaged. Replacement filters are
available from your BLACK+DECKER dealer.
Visit www.blackanddecker.com to locate dealers.
on the
• Remove the old filters as described above.
• Fit the new filters as described above.
MAINTENANCE
Use only mild soap and damp cloth to clean the vac. Never
let any liquid get inside the vac; never immerse any part of
the vac into a liquid.
WARNING:
completely dry before using it.
iMPORTAnT: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service organizations,
always using identical replacement parts.
Troubleshooting
If the product does not work, check the following:
• The charger was correctly plugged in for recharge. (It feels
slightly warm to the touch.)
• The charger cord is not damaged and is
correctly attached.
• The charger is plugged into a working electrical outlet.
• The switch is in the "OFF" position when charging.
For assistance with your product, visit our website
www.blackanddecker.com for the location of the service
center nearest you or call the BLACK+DECKER help line at
1–800–544–6986.
Battery Removal and Disposal
This product uses Lithium Ion rechargeable and recyclable
batteries. When the batteries no longer hold a charge, they
should be removed from the vacuum and recycled. They
must not be incinerated or composted.
The batteries can be taken for disposal to a BLACK+DECKER
into the
Company-Owned or Authorized Service Center. Some local
retailers are also participating in a national recycling program
(see "RBRC® Seal"). Call your local retailer for details. If you
bring the batteries to a BLACK+DECKER Company-Owned or
Authorized Service Center, the Center will arrange to recycle
old batteries. Or, contact your local municipality for proper
disposal instructions in your city/town.
To remove the battery pack for disposal:
1. First, before attempting to disassemble the product,
turn it on and leave it on until the motor completely stops
insuring a complete discharge of the batteries.
2. Using a hex screwdriver, remove the seven screws
securing the two housing halves.
3. Lift the housing cover away from the assembly.
4. Detach all lead connections from battery pack.
5. Remove battery pack and dispose of as per
recommended guidelines.
English
Make sure the vacuum is
7
Publicité
