Manual Address Adjustment; Dmx Control; Indication Of The Firmware Version; Cleaning Of The Unit - IMG STAGELINE RGBL-120DMX Mode D'emploi

2) Press button MENU (5) on the first RGBL-120DMX
(which is directly connected to the light controller)
so many times until the display (10) shows
3) Make sure to press button ENTER (7) within 8 sec-
onds, otherwise the adjusting process will end.
After pressing button ENTER, the 384 LEDs of the light
effect panel light up and the indication
Then the LEDs will go out and the display stops flash-
ing. After another 8 seconds the light effect panel
returns to the previous operating mode.
The start address of the first light effect panel is now
adjusted to 1. The start addresses of the following
RGBL-120DMX units are adjusted to the next free
address in each case:
Start address of the light effect panel No.
Number
of DMX channels
2
4 5
6 7
9 10
15 16
24 25
27 28
Fig. 4 Automatic adjustment of the DMX start addresses

7.3.2 Manual address adjustment

1) Press button MENU (5) so many times until the dis-
play (10) shows
button within 8 seconds, otherwise the adjusting
process will end.
2) Press button ENTER (7). The adjusted address is
shown in a flashing way.
3) Use button DOWN or UP (6) to adjust the address
and memorize it with button ENTER.
pears on the display. After 8 seconds the light effect
panel returns to the previous operating mode.

7.4 DMX control

Once the control signals of the DMX controller are
received, the red LED DMX (3) lights up and the dis-
play shows the start address. The light effect panel can
now be operated with the DMX controller.
Important for DMX control via 6, 9, 15, or 27 channels
(not for 4 or 24 channels):
For RGB control (direct control of the red, green, and
blue LEDs)
adjust DMX channel 1 to 0 – 28 and
DMX channel 2 to 0 – 15.
The show programmes Nos. 1 – 8 are switched on
via DMX channel 1 from a value of 29 onwards and
their running speed or the music control is then
adjusted via DMX channel 2.
For the colour transition programme
adjust DMX channel 1 to 0 – 28 and
DMX channel 2 for the transition speed to 16 – 255.
flashes.
3 4 5 6
9 13 17 21
13 19 25 31
19 28 37 46
31 46 61 76
49 73 97 121
55 82 109 136
. Make sure to press the next

8 Indication of the firmware version

To indicate the version number of the firmware (oper-
.
ating system of the unit):
1) Press button MENU (5) so many times until
(version) appears on the display (10).
2) Press button ENTER (7). The version number will
be indicated, e. g.
3) After 8 seconds, the light effect panel will return to
the previous operating mode.

9 Cleaning of the Unit

The plastic pane in front of the LEDs should be
cleaned at regular intervals, depending on impurities
7
caused by dust, smoke or other particles. Only this will
ensure that the light is radiated at maximum bright-
25
ness. For cleaning, disconnect the mains plug from
37
the socket. Only use a soft, clean cloth and a mild
55
detergent. Then wipe the plastic pane dry.
91
For cleaning the other parts of the housing, only use
a soft, clean cloth. Never use any fluid; it may leak into
145
the unit and cause damage.
163

10 Specifications

Power supply: . . . . . . . . 230 V~ / 50 Hz
Power consumption: . . . 60 VA
Light source: . . . . . . . . . 384 super bright LEDs
Ambient temperature: . . 0 – 40 °C
reap-
Dimensions. . . . . . . . . . 970 × 65 × 85 mm
Weight: . . . . . . . . . . . . . 2.8 kg

10.1 DMX channels

10.1.1 Operation with 4 DMX channels

Channel
1
2
3
music-controlled colour change
4
(channels 1 – 3 w/o function)
stroboscope slow
= version 1.2.
128 red, green, and blue
each
Function
brightness proportion
of the red LEDs
brightness proportion
of the green LEDs
brightness proportion
of the blue LEDs
LEDs off
➞
dimmer: dark bright
➞
fast
stroboscope off
GB
DMX Value
000 – 255
000 – 255
000 – 255
000 – 007
008 – 190
191 – 200
201 – 247
248 – 255
17