Bosch GWS 12-125 S Professional Notice Originale page 10

10 | English
Angle grinder
Constant electronic control
Kickback stop
Weight according to EPTA-Procedure 01:2014
– with low-vibration auxiliary handle
– with standard auxiliary handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Fitting
Fitting Protective Equipment
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
Place the protective guard
(7) onto the holder on the
power tool until the coding
cams of the protective guard
are aligned with the holder.
When doing so, press and
hold the unlocking lever (1).
Press the protective guard
(7) onto the spindle collar un-
til the shoulder of the pro-
tective guard is sitting on the
flange of the power tool and
rotate the protective guard
until it audibly clicks into
place.
Adjust the position of the protective guard (7) to meet the
requirements of the operation. To do this, push the unlock-
ing lever (1) upward and rotate the protective guard (7) into
the required position.
Always position the protective guard (7) such that the
u
two cams on the unlocking lever (1) engage in the
corresponding openings on the protective guard (7).
Adjust the protective guard (7) such that sparking in
u
the direction of the operator is prevented.
The protective guard (7) must only be adjustable
u
while the unlocking lever (1) is actuated. Otherwise,
the power tool must not be used any more under any
circumstances and must be sent to the after-sales ser-
vice.
Note: The coding cams on the protective guard (7) ensure
that only a protective guard that is suitable for the power
tool can be fitted.
1 609 92A 72X | (23.06.2022)
GWS 12-125 S
kg 2.2
kg 2.0
Extraction guard for cutting with a guide block
The extraction guard for cutting with a cutting guide (19) is
fitted in the same way as the protective guard for grinding.
By securing the auxiliary handle (5) with the clip through the
extraction guard on the gearbox housing, the power tool is
firmly attached to the extraction guard. A suitable Bosch
dust extractor can be connected to the extraction guard with
a cutting guide (19). To do so, insert the vacuum hose with
dust extraction adapter into the provided receiving connec-
tion of the extraction guard.
Note: The friction generated by the dust in the vacuum hose
and accessory during extraction causes an electrostatic
charge that the user may experience as static discharge (de-
pending on environmental factors and their physiological
state). Bosch generally recommends using an anti-static va-
cuum hose (accessory) to vacuum up fine dust and dry ma-
terials.
Protective guard for cutting
Always use the protective guard for cutting (6) when
u
cutting with bonded abrasives.
Provide sufficient dust extraction when cutting stone.
u
The protective guard for cutting (6) is fitted in the same way
as the protective guard for grinding (7).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (19) is fit-
ted in the same way as the protective guard for grinding.
Hand guard
Always fit the hand guard (21) when working with the
u
rubber sanding pad (23) or with the cup brush/flap
disc/diamond annular cutter.
Attach the hand guard (21) to the side handle (5).
Side handle
Do not operate your power tool without the side
u
handle (5).
Do not continue to use the power tool if the auxiliary
u
handle is damaged. Do not make any alterations to the
auxiliary handle.
Screw the side handle (5) on the left or right of the machine
head depending on how your are working.
Low-vibration auxiliary handle
GWS 12-150 S
● ●
● ●
2.2
2.1
/ II / II
Screw the auxiliary handle
(5) on the right or left of the
Bosch Power Tools