Bosch 3 601 F4C 8 Notice Originale page 14

OBJ_BUCH-819-004.book Page 13 Thursday, July 7, 2016 10:59 AM
Sabre saw
Cutting depth, max.
– in wood
– in non-alloy steel
– Pipe diameter
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
104 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting board: a =18.5 m/s , K=1.5 m/s
h
Cutting wooden beam: a =19.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, 2014/30/EU, 2006/42/EC
including their amendments and complies with the following
standards: EN 60745-1, EN 60745-2-11, EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Bosch Power Tools
Henk Becker
GSA 1100 E
Executive Vice President
Engineering
mm 230
mm 20
mm 150
Robert Bosch Power Tools GmbH
kg 3.6
70538 Stuttgart, GERMANY
/II
Stuttgart, 01.01.2017
Assembly
Replacing/Inserting the Saw Blade
 Before any work on the machine itself, pull the mains
plug.
 When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
 When changing the saw blade, take care that the saw
blade holder is free of material residue, e. g. wood or
metal shavings.
2
,
Selecting a Saw Blade
2 2
, K=1.5 m/s .
An overview of recommended saw blades can be found at the
beginning of these operating instructions. Use only saw
blades with ½" universal shank. The saw blade should not be
longer than required for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A)
Press the SDS clamping lever 5 forward and guide the saw
blade 1 behind the clamping plate 12 into the saw blade hold-
er 3. Release the SDS clamping lever 5.
 Check the tight seating by pulling on the saw blade. A
loose saw blade can fall out and cause injury.
For certain work, the saw blade 1 can also be turned through
180° (with the teeth pointed upwards) and re-inserted again.
Removing the Saw Blade
 Before removing, allow the saw blade to cool down.
Danger of injury when touching the hot saw blade.
Press the SDS clamping lever 5 forward and pull out the saw
blade 1. Release the SDS clamping lever 5.
Dust/Chip Extraction
 Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dusts can
easily ignite.
English | 13
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 2ME | (7.7.16)