Milwaukee PDD 12 X Instructions D'utilisation page 11

TECHNICAL DATA
Drilling capacity in steel .....................................................................
Drilling capacity in wood ....................................................................
Wood screws (without pre-drilling) ....................................................
No-load speed, 1st gear ....................................................................
No-load speed, 2nd gear ...................................................................
Torque
Low torque*1 ..................................................................................
High torque*1 .................................................................................
Static jamming moment, 1st gear/2nd gear *1 ...............................
Screwing capacity with one fully charged battery (2.4 Ah) : *2
5x40 Soft wood .............................................................................
Drilling capacity with one fully charged battery (2.4 Ah):*2
ø 3 mm Steel plate 1,5 mm ............................................................
ø 6 mm Soft wood 40 mm ..............................................................
Battery voltage ..................................................................................
Drill opening range ............................................................................
Weight with battery with chuck ..........................................................
Weight with battery without chuck .....................................................
Typical A-weighted sound levels:
Sound pressure level (K = 3 dB(A)) .................................................
The noise level when working can exceed 85 dB (A).
Typical weighted acceleration in the hand-arm area .........................
Measured values determined according to EN 60 745.
*1 Measured according to Milwaukee norm N 877318
*2 The values stated are reference values. Actual values might differ, depending on the material and quality of the screws.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the attached leaflet!
Wear ear protectors. Exposure to noise can cause hearing loss.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by
burning them. Milwaukee Distributors offer to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System PBS 3000 chargers for charging System PBS
3000 battery packs. Do not use battery packs from other systems.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash it
off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
SPECIFIED CONDITIONS OF USE
The battery screwdriver is designed for drilling and screwdriving for
independent use away from mains supply.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2, in accordance
with the regulations 98/37/EEC, 89/336/EEC
Manager Product Development
13 ENGLISH
Volker Siegle
PDD 12 X
.............................. 13 mm .............................. 13 mm
.............................. 34 mm .............................. 36 mm
...........................8x80 mm .........................10x50 mm
......................... 0-400 min ....................... 0-480 min
-1
....................... 0-1300 min ..................... 0-1500 min
-1
.............................. 22 Nm .............................. 26 Nm
.............................. 50 Nm .............................. 60 Nm
......................... 31/10 Nm ......................... 40/16 Nm
................................ 370 ................................... 530
................................ 350 ................................... 420
................................ 320 ................................... 400
.............................. 12 V .............................. 14,4 V
........................ 1,5-13 mm ........................ 1,5-13 mm
............................. 2,3 kg ............................... 2,5 kg
............................. 1,9 kg ............................... 2,1 kg
.............................. 73 dB (A) .......................... 70 dB (A)
.......................... < 2,5 m/s ......................... < 2,5 m/s
2
ADVICE FOR OPERATION
The gears can be only changed when the machine is switched off.
BATTERIES
New battery packs reach full loading capacity after 4 - 5 chargings
and dischargings. Battery packs which have not been used for
some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
MAINTENANCE
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: Milwaukee Electric Tool, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
Accessory - Not included in standard equipment,
available as an accessory.
Remove the battery pack before starting any
work on the machine.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste
electrical and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their
life must be collected separately and returned to
an environmentally compatible recycling facility.
PDD 14.4 X LokTor
-1
-1
2