AEG GSL 600 E Notice Originale page 5

fi re, no combustible materials should be located in the
vicinity (spark fl ight zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust
fl ying from the workpiece come into contact with you.
The adjusting nut must be tightened before starting to work
with the machine.
Under the eff ect of extreme electromagnetic interferences
from the outside, temporary variations in the speed of
rotation could arise in particular cases.
Always use and store the grinding disks according to the
manufacturer's instructions.
The workpiece must be fi xed if it is not heavy enough to be
steady. Never move the workpiece towards the rotating disk
by hand.
Make sure that the grinding tool is installed in accordance
with the manufacturer's instructions.
The size of the grinding tool must be suitable for the grinder.
For dusty operations, the machine's ventilation slits must be
kept clear. If necessary, switch off the power to the machine
and remove the dust. Use a non-metallic object for this,
taking care not to damage any of the inner parts.
SPECIFIED CONDITIONS OF USE
This Straight grinder may be used for grinding wood, metal,
plastic, or similar materials, especially in hard accessible
corners and places.
Do not use this product in any other way as stated for
normal use.
Please refer to the instructions supplied by the accessory
manufacturer
The machine is suitable only for working without water.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC and the following harmonized standards
have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-23:2013
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50581:2012
Winnenden, 2018-02-26
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
8 ENGLISH
MAINS CONNECTION
Connect only to single-phase AC current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
Appliances used at many diff erent locations including wet
room and open air must be connected via a residual current
device (FI, RCD, PRCD) of 30mA or less.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Do not let any metal parts reach the airing slots - danger of
short circuit!
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket
before carrying out any work on the machine.
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the
machine.
Wear gloves!
Do not use force.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Class II tool, tool in which protection against
electric shock does not rely on basic
insulation only, but in which additional safety
precautions, such as double insulation or
reinforced insulation, are provided.
There being no provision for protective
earthing or reliance upon installation
conditions.
European Conformity Mark
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
National mark of conformity Ukraine
EurAsian Conformity Mark.
ENGLISH 9