Monacor AXZ-204BVM Mode D'emploi page 45

6.8 Activating / Deactivating signal sounds
Forwarding events to the alarm output
When the following events occur, the internal alarm buzzer
may sound and the alarm relay may respond [output ALARM
(27), can be loaded with 30 V (⎓), 1 A]. The duration of the
alarm sound and the response of the relay can be set via
the corresponding menus and the menu items "Buzzer" and
"Alarm Out".
Event
Alarm triggered via the inputs
SENSOR (27)
Motion in the image
Disk full
Write error on disk
Video signal interrupted
6.9 Settings for live surveillance:
Camera name, image, time display
Call up the menu "Parameter", click the submenu "Display"
and then click the section "Live".
Parameter Record Search Device
Display
Channel CH1
Analog Channels
Channel Name CH1
Show Name Enable
IP Channels
Record Time Enable
Live
OSD Position
Setup
Output
Color
Setup
Image Control
Covert Disable
Privacy Zone
Show Time Enable
Record
Capture
Copy CH1 To
Network
Alarm
Fig. 6-23 Menu for live surveillance
Menu item Function
Channel
To select the camera channel
Channel Name To enter the channel name
Show Name To show the camera name
To show the date and the time of the recording
Record Time
during replay
To move the position of the camera name and the
OSD Position time display (with left mouse button pressed; to
terminate the setting: press right mouse button)
To call up a window for making image settings
Color
(colour, brightness, etc.)
The camera image will not be shown during live
Covert
surveillance
Show Time To show the time
To use the settings of a camera channel for additio-
Copy
nal channels
Default Reset to factory settings
Save
To save the setting
Cancel To exit the menu
6.10 Masking image areas
It is possible to mask specific areas of the image that shall not
be visible (e. g. public ways or places): In each camera image,
four different black squares can be placed. Call up the menu
Menu path
Parameter  Alarm  Alarm
Parameter  Alarm  Motion
Advance  Events  Event Type:
No Space on Disk
Advance  Events  Event Type:
Disk Error
Advance  Events  Event Type:
Video Loss
i
System Advance Shutdown
All Copy
Save Cancel
Default
"Parameter", click the submenu "Display" and then click the
section "Privacy Zone".
Parameter Record Search Device
Display
Channel CH1
Analog Channels
Mask Area Disable
IP Channels
Area Setup 1
Live
Mask Area Setup
Output
Image Control Copy CH1 To
Privacy Zone
Record
Network
Alarm
Fig. 6-24 Menu to mask image areas
Menu item Function
Channel To select the camera channel
Mask Area Set to "Enable" to define the areas to be masked
Area Setup To define a mask, click the appropriate number
1. Click Setup
selected.
2. To move a mask: with the mouse pointer in the
centre of the mask, keep the left mouse button
pressed.
Mask Area
3. To change the size: with the mouse pointer at
the lower right mask corner, keep the left mouse
button pressed.
4. To go back to the menu: click the camera image
with the right mouse button.
To use the settings of a camera channel for additio-
Copy
nal channels
Default Reset to factory settings
Save To save the setting
Cancel To exit the menu
6.11 Setting the motion detection feature
According to the factory settings, the motion detection feature
is enabled for each camera channel and set in such a way
that it is sensitive to motions in the entire image area. When
there is a motion in the image, the symbol
be inserted. The symbol will disappear after 10 seconds when
there is no further motion.
Call up the menu "Parameter", click the submenu "Alarm"
and then click the section "Motion".
Parameter Record Search Device
Display
Channel CH1
Record
Enable Enable
Sensitivity 4
Capture
Area
Setup
Network
Post Recording 30 s
Alarm
Alarm Out
Motion
Show Message Send Email
Record Channel
Alarm
1 2 3 4
Analog Channels
1 2 3 4
IP Channels
Lorem ipsum
Copy CH-1 To
Fig. 6-25 Menu for the motion detection feature
Menu item Function
Channel To select the camera channel
Enable To enable/disable the motion detection feature
The alarm buzzer will sound when a motion is
Buzzer
detected
Sensitivity Sensitivity of the motion detection feature
i
System Advanced Shutdown
2 3 4
All Copy
Default Save
to switch to the camera image
M
(Motion) will
i
System Advance Shutdown
Buzzer Disable
Latch Time 10 s
Full Screen
5 6
All Copy
Default Save
Cancel
Cancel
45