Monacor AXZ-204BVM Mode D'emploi page 38

respective camera image in full-screen mode or to automati-
cally send an e-mail with the snapshot.
Connect the connection [–] of a sensor to the pin G
(ground) and connect the connection [+] of the sensor to the
respective channel input (1 – 16) of the recorder. Proceed in
the same way to connect the other sensors. The menu "Para-
meter", submenu "Alarm", section "Alarm" can be used
to define the alarm display duration, alarm sound duration,
recording duration and alarm contact (NC or NO) and to make
other settings (chapter 6.7).
Output ALARM
A relay with a normally open contact (maximum power rating
of 30 V/1 A) is available as a potential-free alarm output. An
acoustic or optical alarm signal device, for example, can be
connected to the output ALARM.
PTZ connection RS485
The RS-485 interface can be used for remote control of suitable
cameras: e. g. pan, tilt, zoom, iris and motion speed.
Connect the contacts – (= RS-485-A) and + (= RS-485-B) to the
respective contacts of the camera. An additional camera can
be connected in parallel to the connections of the first camera
etc. until all cameras are connected in a chain. To reduce inter-
ference, twisted cables should be used. At the final camera of
the chain, terminate the two cables with a 120 Ω resistor (this
is often possible by means of a switch at the camera).
To be able to address the cameras independently from
the recorder, assign an individual address to the cameras (via
a menu or DIP switch at the camera). At the recorder, set the
address to be used to control the respective camera as well as
the transmission parameters and protocol the camera requires
(chapter 6.12).
5.5 Network
For remote control, connect the jack LAN (26) of the recorder
to a local network or to a router. Always observe the data
security notes in chapter 2!
5.6 Power supply
Connect the power supply unit to the jack 12 V⎓ (29) and to
a mains socket (230 V/ 50 Hz).
6 Setting the Recorder
into Operation
A YouTube video clip (only available in German) from
MONACOR INTERNATIONAL explains the most important steps
of how to set the recorder into operation. The video clip also
shows how easy it is to connect the recorder to a network.
https://youtu.be/13P1Y4PiBmk
38
When the
cameras
monitor
mouse
power supply unit of the recorder
power supply unit for the cameras
have been connected, switch on the recorder with the rocker
switch (30) on the rear. After a few seconds, the MONACOR
logo will appear on the monitor connected:
After approx. 15 seconds, the start page with the "Startup
Wizard" will appear:
15/12/2016 09:53:46
T-CH1
Startup Wizard
R M
CH4
Don't show this window next time.
KEIN VIDEO
Fig. 6-1 Start page: The "Startup Wizard" is displayed; depending on
the recorder model, additional fields for the camera images
are available
6.1 Setting the menu language
The menu language is factory-set to German. To change the
menu language:
1) When a warning appears after switch-on, click
2) In the window "Startup Wizard", click the button
"ABBRUCH". The confirmation box "Are you sure you
want to cancel Startup Wizard?" will appear. Click "OK".
3) To show the toolbar, press the right mouse button or move
the mouse pointer to the centre of the lower edge of the
screen:
Fig. 6-2 Toolbar
4) Click the symbol HAUPTMENÜ (MAIN MENU).
Parameter Aufnahme Suche Gerät
Anzeige
Passage
Analog Channels
CH1
IP Camera
CH2
CH3
Live
CH4
Ausgabe
Image Control
Analog Channels
Privat Zone
Ausgabe
Capture
Netzwerk
Alarm
Fig. 6-3 Hauptmenü (main menu)
5) Click "System" at the top of the menu.
T-CH2
R M
CH3
KEIN VIDEO
Welcome to use the wizard of setup
×
ABBRUCH Weiter
keine Kamer keine Kamer
×
to close it.
i
System Erweitert Schließung
Gerät State
CH1 EIN
CH2 EIN
CH3 EIN
CH4 EIN
CH1 CH2 CH3 CH4
Sicherung ABBRUCH