Kenwood MultiPro Compact+ FDM313SS Manuel D'instructions page 12

To Use Your Food Processor
Illustrations –
1 Fit the detachable drive shaft onto the power
unit.
2 Then fit the bowl by aligning the
bowl with the on the power unit, turn
clockwise until it locks
3 Fit an attachment over the bowl drive shaft.
Always fit the bowl and attachment onto the
processor before adding ingredients.
4 Fit the lid - ensuring the top of the drive
shaft/tool locates into the centre of the lid.
Do not use the lid to operate the processor,
always use the on/off speed control.
5 Plug in, switch on and select a speed. (Refer
to the recommended usage chart).
The processor will not operate if the bowl
or lid are not fitted correctly into the
interlock. Check that the feed tube and
bowl handle are situated to the right front
hand corner.
Use the pulse (P) for short bursts. The pulse
will operate for as long as the control is held
in position.
6 Reverse the above procedure to remove the
lid, attachments and bowl.
Always switch off and unplug before
removing the lid.
Important
Your processor is not suitable for crushing
or grinding coffee beans, or converting
granulated sugar to caster sugar.
When adding almond essence or flavouring
to mixtures avoid contact with the plastic as
this may result in permanent marking.
Weighing Function
Illustration
Your food processor is fitted with a built in
weighing function to allow ingredients to be
weighed straight into the bowl or blender goblet.
The Maximum weighing capacity is 3kg.
To Use The Weighing Function
1 Always fit the bowl, detachable drive shaft
and attachment or blender goblet onto the
power unit before adding ingredients.
2 Plug in – the display screen will remain blank.
3 Press the ON/ZERO button once and the
display screen will light up.
4 Press the (kg/lb) button to select either
grams or ounces. The display will default to
kg/g when first switched on.
The unit weighs in 1g increments and
teaspoon/tablespoon measures are
recommended for weighing small quantities.
on the
.
To zero press the ON/ZERO button once.
5 Weigh the required ingredients straight into
the bowl or goblet.
6 After all the ingredients are weighed fit the lid
and select a speed to operate the processor.
The weight of any additional ingredients
added down the feed tube whilst the
processor is running will not be shown on the
display screen.
The display screen can be turned off manually
by pressing and holding down the ON/ZERO
button for a few seconds.
Refer to the troubleshooting guide if you
experience any problems with operating the
weighing function.
Weighing Tray
A removable weighing tray is supplied for
weighing ingredients without the bowl or
blender.
To use, place the tray on top of the power unit
and turn clockwise to secure. Then follow steps 2
to 4 under 'To Use The Weighing Function'.
To remove, rotate the tray anti-clockwise and lift
off.
Using The Attachments
Refer to recommended usage chart
for each attachment.
14A
Plastic Blender
To Use Your Blender
Illustrations
1 Fit the sealing ring into the blade
assembly - ensuring the seal is located
correctly in the grooved area.
Leaking will occur if the seal is damaged or
incorrectly fitted.
2 Hold the underside of the blade assembly
and insert the blades into the goblet - turn
anti-clockwise until it is secure. Refer to
the graphics on the underside of the blade
assembly as follows:
- Unlocked position
- Locked position
3 Put your ingredients into the goblet.
4 Fit the lid onto the goblet and turn clockwise
until it clicks. Fit the filler cap.
5 Place the blender onto the power unit, align
the on the blender with the
power unit and turn clockwise to lock
The appliance will not operate if the blender
is incorrectly fitted to the interlock.
6
(if supplied)
–
on the
.