Télécharger Imprimer la page

IPC 505 Manuel D'instructions page 19

Masquer les pouces Voir aussi pour 505:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 24
4.1 - STARTING
ATTENTION: the machine must be used by authorised personnel
only. DO NOT leave the machine UNATTENDED
when it is running. Do not use the machine to soak up
liquid. Take out the key before leaving the machine.
KEEP THE MACHINE OUT OF CHLIDREN'S
REACH.
4.1.1 - Electrical version
To start the machine carry out the following operations:
- Make sure the side brush pos. 1 Fig. 3. is OFF.
- Turn the switch pos. 2 Fig. 3 ON. Wait 10 seconds before the machine
sets off.
- Before the machine sets working,check the indicator pos. 4 Fig. 3, to
assess whether the battery is fully charged. If it is not, proceed to
recharge it.
- Pull the traction lever pos. 6 Fig. 3, to start cleaning.
If necessary, operate lever pos. 1 Fig. 3, by turning it ON, to start the
side brush. If you have been using the side brush, at the end of your
work remeber to turn it OFF. Switch off the machine and remove the
key from the control panel.
An automatic device will prevent you from using the
machine beyond a certain battery charge limit.
When this limit is reached, the machine will stop and the battery must
be recharged.
4.1.2 - Engine version
- Make sure the side brush pos. 1 Fig. 3, is OFF.
- Ensure that engine has enough petrol and oil.
- Switch accelerator lever pos. 5 Fig. 3, to START.
- Place the key pos. 2 Fig. 3 on ON position.
- Open up fuel tap pos. 3 Fig. 4.
- If the engine is cold, operate the choke lever pos. 2 Fig. 4.
- Operate the start handle pos. 7 Fig. 4.
- As soon as the engine starts running, shut off the choke lever pos. 2
Fig. 4 if it was operated.
- Act on the accelerator pos. 5 Fig. 3, to reach the required speed.
- At the end of your work, if you have been using the side brush pos. 1 Fig.
3 turn it OFF. Turn the accelerator lever to START and turn off the
machine with the key pos. 2 Fig. 3. Close up fuel tap pos. 3 Fig. 4.
1
2
5
3
6
7
1) Fuel tank cap
2) Choke lever
3) Petrol tap
4) Self-winding ignition cable
5) Air filter
6) Throttle valve lever
7) Start handle
8
9
4
12
10
13
14
8) Tank
9) Engine switch
10) Engine name plate
11) Plug
12) Muffler
13) Oil filling cap
14) Oil drain plug
Fig. 4 and 5
ENGLISH (Translation of original instructions)
4.2 - CORRECT OPERATION
After you have become conversant with the operations required to start
the machine,you can actually start using the sweeper to obtain the best
results,it is always wise to take a few precautions. These will help you
to get the best from your machine and reduce damage to a minimum.
In particular:
- do not use the machine to clean up wires,ropes or straps or soak up
water and other liquids.
- When using the machine on light but bulky material (sheets of paper,
leaves, etc.), raise the front part of the machine by pressing down the
handlebar so that the machine can tackle the rubbish.
- Operate the filter shaker at the end of your work (see the Panel filter
section).
- Make sure the centre brush is correctly regulated (see the section on
Adjusting the centre brush).
DANGER: petrol is highly inflammable. Keep your fuel in
containers designated for the purpose. Top up your fuel
tank ONLY when the engine is off. Do not remove the fuel
tank cap when the motor is running or hot. Always fill your
fuel tank in open air or in a sufficiently ventilated area.
Do not smoke during this operation and do not use naked
flames. If you spill fuel during this operation, DO NOT
attempt to start the engine but wait for the vapour to
evaporate.
Always turn off the engine:
- Before leaving the machine unattended;
- Before filling the fuel tank;
- Before carrying out any work on the machine.
4.3 - CLEANING THE WASTE BINS
Before carrying out this operation, make sure all parts are off.
(*) ATTENTION: WASTES MUST BE DISPOSED OF
4.3.1 - Front bin
- Lift and turn the two bin locks.
- Grasp the handle/s and remove the bin by pulling it upwards.
- Empty the bin (*).
To put the bin back in place:
- Put the bin back in the machine from the top.
- Turn and lower the two locks.
11
4.3.2 - Rear bin
- Lift and turn the two bin locks.
- Grasp the handle and pull the bin out of the machine.
- Empty the bin (*).
To put the bin back in place:
- Fit the bin back into the machine.
- Turn and press the two locks.
STRICTLY IN ACCORDANCE TO THE
LAW.
GB
7

Publicité

loading

Ce manuel est également adapté pour:

705