Bort MASTER ECO Mode D'emploi page 12

the right (with a wrench or adjustable pliers) until
the mounting loops are fixed (3) with respect to the
mounting rails (Fig. 8.2).
Make sure that all three mounting loops are locked.
Disposer is installed.
4. Run water into the sink, then check the connec-
tions for leaks.
5. Insert the noise absorbing screen into the drain
hole flat side up. (Fig.8.3)
8. CONNECTING THE OUTLET PIPE
• To the DRAIN PIPE ATTENTION!
• It is recommended to wear protective goggles
when installing the disposer.
• For all models, the drain pipe is connected using
a screw connection (Fig. 9.2). First connect the hy-
draulic lock to the disposer and then to the drain.
For the connection a siphon with smooth walls
should be used.
• Use a sanitary sealant only for connecting the
flange of the sink with the disposer.
• Do not use sealants for threaded pipe connec-
tions or anaerobic screwed sealants. They can
damage the product.
• Regularly check the disposer and fittings for wa-
ter leaks, since leaks water can cause damage to
property.
• The manufacturer is not responsible for damage
to property as a result of water leaks.
INSTALLING THE DRAINAGE SYSTEM
1. Put the flange (2) on the drain pipe Insert the rub-
ber seal (1). Fasten drain tube, tightly pulling it to
the body disposer with screws (4). (Fig. 9.1)
9. CONNECTING THE DISPOSER TO THE ELECTRI-
CAL NETWORK
ATTENTION! ELECTRIC SHOCK CURRENT
To prevent electric shock, turn off the power before
installing or servicing the product.
If you are not qualified enough, call an electrician to
connect the product to the power.
If a three–pin grounding–type plug is used to con-
nect a three–contact outlet with ground.
Do not modify the design of the plug supplied with
the device.
Improper equipment grounding may cause electric
shock current.
All electrical connections must comply with the
electrical and norms.
Do not connect the ground to the feed pipe gas.
Do not power on the distribution shield until you
have installed the sockets with proper grounding.
If the power cord is damaged, it must be replaced at
the service center.
NOTE: Access to a grounded outlet is required. In-
stalling all additional outlets must be carried out by
a qualified electrician, and all outlets must be prop-
erly grounded.
Turn ON/OFF device
Depending on the models BORT disposer are
equipped with two types of control: a wireless (wall)
switch or a pneumatic switch.
Wireless (wall) switch
The disposer of the "Control and FullControl" series
are equipped with a wireless wall mount switch.
The switch should be located in a convenient (safe
for children) place above the table top.
For instal the switch to the wall, use double–sided
tape.
For activate / deactivate the device, hold down the
key for 2–3 seconds.
Battery type: Voltage: 12V; Size: A27
Air switch
Disposer is equipped with an air switch and a con-
necting pipe (except "Control" series).
INSTALLATION OF AIR SWITCH
1. Drill a hole with a diameter of 32 mm in suitable
top or top the panel of a sink. Some sinks may al-
ready have a suitable A hole for the opening of
which is necessary remove the cover.
2. Unscrew the nut from the body of the push but-
ton, while holding the stainless steel washer and
rubber gasket in place. Place one end of the PVC
tube on the spout on the body Press the other end
to A hole in the table top and a nut located under
the countertop. (Fig. 10.2)
3. Place the push button housing in the hole and
tighten the nut underneath countertop (enough
arm effort). Do not use the key to tighten nut. (Fig.
10.3)
4. Take the other end of the duct and tightly put it
on the spout of the air switch located on the bot-
tom of the disposer. (Fig.10.4) Hand tighten the
clamping nut. The disposer installation is complete.
Before using the product, read all of the instruc-
12