Bort MASTER ECO Mode D'emploi page 11

The complete set is shown on the package. Dur-
ing unpacking the device, check the complete
set.
2. DISCONNECTION OF THE DROP HORN
ATTENTION!
At the time of installation of the device is recom-
mended Wear safety glasses. Loosen the nut (1) on
the top of the water trap (4) with a pipe wrench (Fig.
3.1). relative humidity not more than 80%. Loosen
the nut (2) on the top of the extension pipe. Re-
move the extension pipe.
Loosen the nut (3) at the bottom of the washing
flange.
Push the washing flange upwards through drain
hole of the sink and remove it (Fig. 3.2).
CLEAN THE WASH FAN WRAPPING PLACE FROM THE
SEALANT OR THE GARBAGE.
NOTE: It may be necessary to expand the drain hole
for installation flange fastening disposer. Equip-
ment for extending the drainage hole is purchased
separately.
3. DISASSEMBLY OF THE ASSEMBLY UNIT
Turn over the assembly (Fig.4.1) and loosen the
three fixing screws (1) The access to the ring (2).
Disconnect the retaining ring from the flange with
a screwdriver. Now the assembly unit can be disas-
sembled.
4. ATTACHING THE FIXING ASSEMBLY TO
WASHING Fig.5.1.
1. Install one or two rubber gaskets (2) under the
washing flange (1). Make sure that The drainage
hole is not clogged, and set to flange washer / gas-
ket. In order to The flange of the sink became in
place, you need to crush it with a heavy load. (To
avoid scratches, use a towel as a lining.)
2. Put the second rubber part on the bottom of the
kitchen sink a gasket (2), a cardboard gasket (op-
tional) (3) and a metal support ring (4) (flat side up).
3. While holding the second rubber gasket, card-
board padding (optional) and a metal support ring,
put the mounting ring (5) on the flange of the sink
so that it aligned with the support ring.
4. Pressing tightly to the bottom of the sink rubber
gasket, cardboard gasket, support ring and mount-
ing ring, slide the snap ring (7) onto the flange of
the sink so that it snaps into the flange groove.
5. Tighten the three fixing screws (6) to The fixing
assembly was tight and evenly pressed to the sink.
5. CLEANING THE DRAIN PIPE
If you do not clean the drain pipe, it can clog.
1. Remove the water trap. (Fig.6.1)
2. Using a cleaner, remove all solid precipitation in
the horizontal part of the drainage pipes, moving
with side of the siphon towards the main pipe.
IF THE DISHWASHER WILL NOT BE CONNECTED TO
THE DISPOSER, GO TO PART 7 OF THIS INSTRUCTION
6. CONNECTING THE DISHWASHER MACHINES
AND TRANSFER CONNECTION
If the sink is full of liquid it can be discharged into
the disposer through the inlet in its upper parts.
(Fig. 7.2)
On all models inside the intake pipe there is parti-
tion. The partition must be removed (Fig. 7.1).
REMOVING THE PLATE / PARTITION
1. Place the disposer on one side and place it screw-
driver into the connection for the dishwasher, push-
ing it until it will not rest against the partition in the
end of the branch pipe.
2. With several blows of the hammer, knock out the
septum in the branch pipe (Fig. 7.1).
3. Remove the embossed partition from the dis-
poser bowl. If necessary to connect the dishwasher,
then it should be connected to the inlet of the over-
flow outlet pipes To connect to the overflow inlet,
remove the exhaust pipe cover by unscrewing the
cover (Fig. 7.3).
7. CONNECTING THE DISPOSER TO THE FIXING
UNIT ATTENTION!
To avoid injury, follow the so that during the remov-
al and installation of a part Your body was not under
the disposer; during the installation it is possible to
drop it.
Remove any objects from the grinding chamber
product before installing it on the sink.
1. Install the product in such a way that provide
easy access to the restart button engine located in
the lower part of the body. Do not block this place
with any objects.
2. Place the disposer with three mounting loops
(1) into the sliding position by mounting rails (2).
(Fig. 8.1)
3. Lift the disposer, insert the top end (installation
gasket) in the mounting and turn the setting ring to
11