Chamberlain Whisper Drive SECURITY+ 459950 Manuel Du Propriétaire page 32

Using the Wall-Mounted
Door control
THE SMART CONTROL PANEL™
Press the push button to
open or close the door.
Press again to reverse
the door during the
closing cycle or to stop
the door while it's
opening.
This door control
contains a motion
detector that will
automatically turn on the light when it detects a person
entering the garage. This feature can be easily turned off for
extended work light use.
Light Feature
LIGHT
Press the Light button to turn the opener light on or off. It will
not control the opener lights when the door is in motion. If
you turn it on and then activate the opener, the light will
remain on for 4-1/2 minutes. Press again to turn it off
sooner. The 4-1/2 minute interval can be changed to 1-1/2,
2-1/2 or 3-1/2 minutes as follows: Press and hold the Lock
button until the light blinks (about 10 seconds). A single blink
indicates that the timer is reset to 1-1/2 minutes. Repeat the
procedure and the light will blink twice, resetting the timer to
2-1/2 minutes. Repeat again for a 3-1/2 minute interval, etc.,
up to a maximum of four blinks and 4-1/2 minutes.
When using the opener lights as working lights, we
recommend that you first disable the motion sensor.
Lock Feature
LOCK
Designed to prevent operation of the door from hand-held
remote controls. However, the door will open and close from
the Door Control, the Outside Keylock and the
Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds.
The push bar light will flash as long as the Lock feature
is on.
To turn off, press and hold the Lock button again for
2 seconds.The push bar light will stop flashing. The Lock
feature will also turn off whenever the "learn" button
is activated.
Motion Detecting Light Feature
The opener light will turn on automatically when a person
walks in front of the wall-mounted door control. This feature
works by detecting motion and body heat and may not work
in temperatures around 100˚F, 37.7˚C. The opener light will
come on for 5 minutes, then shut off automatically if no
additional motion or heat differential is calculated.
To disable this feature, press the Motion Detecting
Light On/Off button on the left side of the door
control.
We recommend that you disable the motion sensor when
using the opener lights as working lights. Otherwise, they will
turn off automatically if you are working beyond the sensor's
range.
Motion Sensing
ON/OFF
Prog <LEARN>
Hour
Minute
Language
Degrees (F/C)
Lock Button
(Prog) Learn Feature
The door control is equipped with a Prog <LEARN>
button to assist in learning remote controls to the unit.
Press the Prog <LEARN> button once to initiate LEARN
mode and the display will show 'Learn Remote Control -
Push Bar Press Learn Button Again to Confirm'. Press the Prog
<LEARN> button a second time and the display will show
'Learn Mode - Press Remote Control Button to Learn
Remote.' Press the button of the remote control to be
learned and the worklight will blink to confirm the remote
Light Button
control has been learned.
H M
Press or hold either of these side buttons to increment
the hour or minute displayed on the LCD display.
(Lang) Language Feature
Press this side button to toggle between the three
languages - English, Spanish, and French.
Degrees F/C Feature
Press this side button to toggle the temperature units
between Fahrenheit and Celsius.
Additional feature when used with the 3-Button
hand-held remote
To control the opener lights:
In addition to operating the door, you
may program the remote to operate
the lights.
1. With the door closed, press and
hold a small remote button that you want to control the
light.
2. Press and hold the Light button on the door control.
3. While holding the Light button, press and hold the Lock
button on the door control.
4. After the opener lights flash, release all buttons.
32
Hour & Minute Feature