Publicité
Les langues disponibles
Les langues disponibles
1. Product and package contents
Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector
1 x external PSU
2. Preliminary warning notices
1.
Please use this device only according to these operating instructions.
2.
Do not use the device if there are any visible damages on housing, connector
panels, power supplies or power cords.
3.
Never look directly into the light source of a laser projector. Danger of dama-
ge to the eyes or even blindness in extreme circumstances!
Do not operate the device at high humidity, rain or in dusty
4.
surroundings.
5.
Protect device against dripping or splashing water. Do not place
any liquid filled containers near to this device.
Any warranty claims are void if the warranty label is removed or tampered
with in any way.
3. Initial operations, safety instructions
1.
Make sure to use correct voltage;
see information on device & in this
manual.
Make sure that the device is not
2.
connected to mains during ins-
tallation.
3.
Installation has to be done by
technical experienced and qua-
lified persons according to safe-
ty regulations of the respective
country.
4.
Always ensure that maximum
permissible exposure (MPE) is
not exceeded in areas accessib-
le to the public or members of
staff.
5.
In some countries an additional
inspection by technical control
institutes could be necessary.
1 x manual
6.
Connect an easily accessible
interlock connector or circuit
breaker to the projector.
7.
The power supply should be easily
accessible.
8.
When installing the laser keep
mount it with a minimum distance
of 15 cm from walls and objects.
9.
For safe setup e.g. on walls or
ceilings please use a safety cord.
The safety cord should be able to
withstand tenfold the weight of
the device. Please follow the ac-
cident prevention regulations of
professional associations and/or
comparable regulations for acci-
dent prevention.
10. If the device has been exposed to
great temperature changes, do
not switch it on immediately. Con-
densation (or any moisture/water
formed) may damage device.
11. Never use dimmer, RC or other
electronically switched sockets.
Whenever possible, do not use the
laser projector together with large
appliances (especially fog machi-
nes) on the same mains!
4. Working on the device
1.
This product has no user serviceable parts inside and
should only be maintained and serviced by a quali-
fied engineer.
2.
Be sure that the mains plug is not connected to
the power supply while installing or opening
the device (e.g. for cleaning).
3.
Take off all reflecting things like rings, watches etc.
before start working with or at the projector.
4.
Use only non-reflecting tools to work on device.
5.
Wear protective clothing (like goggles, gloves etc.) according to laser power
and wavelength of the laser.
5. Service notes
•
Moisture and heat can reduce lifetime of the laser system dramatically and ex-
pires any warranty claim.
•
Quick on/off switching of this device will reduce durability of the laser diode
dramatically.
•
Avoid sharp knocks and shocks to this device and ensure sufficient protection
during transportation. Look after your Laserworld product.
•
To increase durability of your laser, protect device against overheating:
-
Always ensure sufficient ventilation.
-
Do not face spotlights (especially moving heads) to the device.
-
Check temperature after approx. 30 minutes with each new installation. If ne-
cessary install the projector at a place with different temperature.
12. Ensure sufficient ventilation and
do not place the device on any
warm or heat radiating surface. Es-
pecially the ventilation openings
must not be covered!
13. Ensure that device does not get
overheated. Make sure that the
device is not exposed to spotlights
(especially moving heads). Heat of
spotlights could overheat laser in a
little while and leads to a degrada-
tion of performance.
Publicité
