cecotec CONGA ROCKSTAR 2500 X-TREME Manuel D'instructions page 26

ENGLISH
Using the vacuum cleaner
- Press the On/off button to turn the device on and off.
- Press the speed button repeatedly to select the device operating speed: LOW, MED, HIGH
and AUTO. The device is by default switched on in LOW mode.
- If you select the AUTO mode, the device will automatically adjust suction power according
to the concentration of dust and the type of surface.
- When operating at high speed, if the battery is at 20% or lower, the device will automatically
switch to medium speed in order to lengthen the battery life.
Using the brush head
- Assemble the vacuuming tube to the brush head and then to the main body, as described
in the product assembly section.
- Press the On/off button to turn the device on and off.
- Press the speed selector to adjust the power level between LOW, MED, HIGH and AUTO
modes.
- The brush head removes dust from carpets, hard and soft floors, and tiles.
- If too many particles or fibres are vacuumed, or if a child touches the brush during operation
by accident, the rotary brush stops spinning automatically in order to prevent tangles and
possible damage.
Accessories
Fig. 4
This device includes different accessories that allow cleaning different types of surfaces,
objects and dirt. Some of them are suitable for the upright vacuum cleaner, and others are
preferably used with the handheld one.
Jaliscazo brush
Assemble this brush to the upright vacuum cleaner. This brush is especially designed for
cleaning hard floors, but can be used to efficiently clean soft floors too.
2-in-1 wide accessory for corners and furniture
Fig. 5
This accessory is preferably used with the handheld vacuum cleaner and allows cleaning
furniture without damaging it and reaching less accessible dirt in corners.
2-in-1 narrow accessory for corners and furniture
Fig. 6
This accessory is preferably used with the handheld vacuum cleaner and allows cleaning
furniture without damaging it and reaching less accessible dirt in corners.
50
Wall charging base installation
Fig. 7
1. Place the charging base on the wall and mark the 3 to the holes to be drilled in order
to fix the base. Take into account the height of the installation, it is important that the
brush head rests on the floor to avoid the charging base from holding all the weight of
the vacuum cleaner.
2. Drill 3 holes in the wall (previously marked) and insert the pegs and M4 x 32 mm screws.
3. Make sure that the charging base is securely fixed on the wall, place the vacuum cleaner
on the charging base by putting the vacuum cleaner charging terminals into contact with
the terminals of the charging base (plastic tab).
4. Once the wall charging base is installed, the charging port must be connected to the
power adapter, and then the device can be charged by sliding it from top to bottom into
the wall charging base. Fig. 8
Charge and display
- When the battery percentage is 20 % or below, the device will automatically enter
low consumption mode. It is recommended to charge the device when it reaches this
percentage.
- The battery must be charged on the charging base while connected to the main body.
Connect one of the ends of the power adapter to the power supply and the other to the
charging base. Fig. 8
- During charging, the charge light indicator will turn on red and the display will show the
current charge percentage. When the device is fully charged, the battery indicator will turn
green and the display will show 100 %. Fig. 9
- You can also charge the battery without using the charging base. It can be charged when
the battery is installed or not in the device. Connect the adapter and connect the other end
to the battery, paying attention to the direction. Once it is properly connected, the charge
light indicator will turn on red and will turn green once the charge is complete. Fig. 10-11
5. CLEANING AND MAINTENANCE
- Turn the appliance off, unplug it from the power supply and allow it to cool down before
cleaning it.
- Use a soft, slightly dampened cloth to clean the device surface.
- Never immerse the device in water or other liquids, do not allow liquids to enter the device.
- Do not use abrasive cleaners or scouring pads to clean the product.
- Do not leave the device in a place with direct sunlight.
- Do not leave the device in a wet place after cleaning it.
- After the brush has been used for a long time, bristles might start to tangle with hair and
other particles. Clean it in order for it to operate correctly again.
ENGLISH
CONGA ROCKSTAR 2500 X-TREME 51